관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size
| 분야 | 05.06 : 기체화 연료; 석탄 및 코커스 |
|---|---|
| 적용범위 | 1.1 This test method covers procedures for determining the sieve analysis of coal and designating the size of coal from sieve analysis data. Raw as well as prepared (crushed, cleaned or screened) coals can be tested by this test method. 1.2 This test method explains how to designate coal sizes from the results of sieve analysis data in order to represent the condition of the coal as sold. In the case of special mixtures or coals with noncontinuous ranges of sizes, a sufficiently complete sieve analysis must be made to properly describe the size distribution. 1.3 This test method is not applicable for determining the sieve analysis nor for designating the size of pulverized coal. (See Note 1.) Size fractions down to and including 38 μm [No. 400 U.S.A. Standard Series] can be treated by the methods discussed in this test method. Methods for handling size fractions below 38 μm [No. 400] will be developed by this committee. Note 1: For powdered or pulverized coal as is fired into steam boilers, refer to Test Method D197. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 75.160.10 : 고체 연료 |
| 페이지수 | 10 |
| Edition | 87(2019)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D4749/D4749M-87(2019)e1 | Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size | 2019-11-01 | 표준 |
관련상품이 존재하지 않습니다.
ASTM D3175-20 - Standard Test Method for Volatile Matter in the Analysis Sample of Coal and Coke 상세보기
IEEE 518-1982 - IEEE Guide for the Installation of Electrical Equipment to Minimize Electrical Noise Inputs to Controllers from External Sources 상세보기
IEEE 502-1985 - IEEE Guide for Protection, Interlocking, and Control of Fossil-Fueled Unit-Connected Steam Stations 상세보기
IEEE 242-2001 - IEEE Recommended Practice for Protection and Coordination of Industrial and Commercial Power Systems (IEEE Buff Book) 상세보기
IEEE 115A-1987 - IEEE Standard Procedures for Obtaining Synchronous Machine Parameters by Standstill Frequency Response Testing 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
