관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
---|---|
적용범위 | 1.1 This practice describes a procedure to qualitatively describe the nature of banded or oriented microstructures based on the morphological appearance of the microstructure. 1.2 This practice describes stereological procedures for quantitative measurement of the degree of microstructural banding or orientation. Note 1: Although stereological measurement methods are used to assess the degree of banding or alignment, the measurements are only made on planes parallel to the deformation direction (that is, a longitudinal plane) and the three-dimensional characteristics of the banding or alignment are not evaluated. 1.3 This practice describes a microindentation hardness test procedure for assessing the magnitude of the hardness differences present in banded heat-treated steels. For fully martensitic carbon and alloy steels (0.10–0.65 %C), in the as-quenched condition, the carbon content of the matrix and segregate may be estimated from the microindentation hardness values. 1.4 This practice does not cover chemical analytical methods for evaluating banded structures. 1.5 This practice deals only with the recommended test methods and nothing in it should be construed as defining or establishing limits of acceptability. 1.6 The measured values are stated in SI units, which are regarded as standard. Equivalent inch-pound values, when listed, are in parentheses and may be approximate. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 07.030 : 물리학. 화학 |
페이지수 | 29 |
Edition | 19 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM E1268-19 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2019-06-01 | 표준 |
2 | ASTM E1268-19 REDLINE | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2019-06-01 | 표준 |
3 | ASTM E1268-18 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2018-06-01 | 구판 |
4 | ASTM E1268-01(2016) | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2016-01-01 | 구판 |
5 | ASTM E1268-01(2007) | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2007-05-01 | 구판 |
6 | ASTM E1268-99 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2001-12-10 | 구판 |
7 | ASTM E1268-01 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures | 2001-12-10 | 구판 |
관련상품이 존재하지 않습니다.
JIS G 0404:2014 - Steel and steel products -- General technical delivery requirements 상세보기
ASTM E562-19 - Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count 상세보기
ASTM A370-19e1 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products 상세보기
ASTM C202-19 - Standard Test Method for Thermal Conductivity of Refractory Brick 상세보기
ASTM B688-18 - Standard Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08367) Plate, Sheet, and Strip 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기