관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure
| 분야 | 07.02 : 섬유 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine. 1.1.1 The CRE-type tensile testing machine has become the preferred test apparatus for determining trapezoid tearing strength. It is recognized that some constant-rate-of-traverse-type (CRT) tensile testing machines continue to be used. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. The conditions for use of the CRT-type tensile tester are included in Appendix X1. 1.2 This test method applies to most fabrics including woven fabrics, air bag fabrics, blankets, napped fabrics, knitted fabrics, layered fabrics, pile, and nonwoven fabrics. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. Instructions are provided for testing specimens with or without wetting. 1.3 Tearing strength, as measured in this test method, requires that the tear be initiated before testing. The reported value obtained is not directly related to the force required to initiate or start a tear. 1.4 Two calculations for trapezoid tearing strength are provided: the single-peak force and the average of five highest peak forces. 1.5 The values stated in SI units are to be regarded as the standard. The values stated in inch-pound units may be approximate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 59.080.30 : 직물류 |
| 페이지수 | 7 |
| Edition | 15(2019) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5587-15(2024) | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2024-01-01 | 표준 |
| 2 | ASTM D5587-15(2019) | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2019-07-01 | 구판 |
| 3 | ASTM D5587-15 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2015-07-01 | 구판 |
| 4 | ASTM D5587-15 REDLINE | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2015-07-01 | 구판 |
| 5 | ASTM D5587-14 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2014-02-15 | 구판 |
| 6 | ASTM D5587-08 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2008-08-01 | 구판 |
| 7 | ASTM D5587-07ae1 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2007-12-01 | 구판 |
| 8 | ASTM D5587-07a | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2007-12-01 | 구판 |
| 9 | ASTM D5587-07 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2007-07-01 | 구판 |
| 10 | ASTM D5587-05 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2005-03-01 | 구판 |
| 11 | ASTM D5587-03 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 2003-10-01 | 구판 |
| 12 | ASTM D5587-96(2003) | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 1996-02-10 | 구판 |
| 13 | ASTM D5587-96 | Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure | 1996-02-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D5035-11(2019) - Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) 상세보기
ASTM D3107-07(2019) - Standard Test Methods for Stretch Properties of Fabrics Woven from Stretch Yarns 상세보기
ASTM D2724-19 - Standard Test Method for Bond Strength of Bonded, Fused, and Laminated Apparel Fabrics 상세보기
ASTM D4704-13(2017) - Standard Test Method for Tearing Strength, Tongue Tear of Leather 상세보기
ASTM D1813-13(2017) - Standard Test Method for Measuring Thickness of Leather Test Specimens 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
