관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This fire-test-response test method covers a small-scale laboratory screening procedure for comparing the relative linear rate of burning or extent and time of burning, or both, of plastics in the form of bars, molded or cut from sheets, plates, or panels, and tested in the horizontal position. Note 1: This test method, and test method A of IEC 60695-11-10 are technically equivalent. Note 2: For additional information on materials which do not burn to the first reference mark by this test, see Test Method D3801. 1.2 This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standard applicable to such equipment. 1.3 The classification system described in Appendix X1 is intended for quality assurance and the preselection of component materials for products. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see 9.2. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
13.220.40 : 자재 및 제품의 점화성 및 연소성
83.080.01 : 플라스틱 일반 |
| 페이지수 | 8 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D635-22 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2022-07-01 | 표준 |
| 2 | ASTM D635-22 REDLINE | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2022-07-01 | 표준 |
| 3 | ASTM D635-18 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2018-11-01 | 구판 |
| 4 | ASTM D635-18 REDLINE | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2018-11-01 | 구판 |
| 5 | ASTM D635-14 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2014-12-01 | 구판 |
| 6 | ASTM D635-10 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2010-07-01 | 구판 |
| 7 | ASTM D635-06 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2006-05-01 | 구판 |
| 8 | ASTM D635-03 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 2003-07-10 | 구판 |
| 9 | ASTM D635-98 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 1998-07-10 | 구판 |
| 10 | ASTM D635-97 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position | 구판 |
관련상품이 존재하지 않습니다.
IEEE 946-2004 - IEEE Recommended Practice for the Design of DC Auxiliary Power Systems for Generating Systems 상세보기
IEEE C62.41.2-2002 - IEEE Recommended Practice on Characterization of Surges in Low-Voltage (1000 V and less) AC Power Circuits 상세보기
IEEE 572-2006 - IEEE Standard for Qualification of Class 1E Connection Assemblies for Nuclear Power Generating Stations 상세보기
IEEE 334-2006 - IEEE Standard for Qualifying Continuous Duty Class 1E Motors for Nuclear Power Generating Stations 상세보기
IEEE 382-2006 - IEEE Standard for Qualification of Safety-Related Actuators for Nuclear Power Generating Stations 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
