관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Indentation Hardness of Organic Coatings
| 분야 | 06.01 : 페인트-화학적, 물리적, 광학적특성 시험; 현상 | ||||||
|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 These test methods cover the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass. 1.2 Two methods are covered as follows:
1.3 Method A, which has the greater precision, provides hardness values in terms of Knoop Hardness Number (KHN). Method B provides hardness in terms of Pfund Hardness Number (PHN). Although the hardness value scales of these methods differ, the methods agree in the ranking of coating hardness. 1.4 Test Method A of these test methods is similar in content (but not technically equivalent) to ISO 6441-1 and ISO 6441-2. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 국제분류(ICS)코드 | 25.220.60 : 유기 도장 | ||||||
| 페이지수 | 5 | ||||||
| Edition | 13(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1474/D1474M-13(2023) | Standard Test Methods for Indentation Hardness of Organic Coatings | 2023-02-01 | 표준 |
| 2 | ASTM D1474/D1474M-13(2018) | Standard Test Methods for Indentation Hardness of Organic Coatings | 2018-11-01 | 구판 |
| 3 | ASTM D1474/D1474M-13 | Standard Test Methods for Indentation Hardness of Organic Coatings | 2008-07-01 | 구판 |
관련상품이 존재하지 않습니다.
SAE J2527_201709 - Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus 상세보기
ASTM D7187-20 - Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching 상세보기
ASTM D610-08(2019) - Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces 상세보기
ASTM D7869-17 - Standard Practice for Xenon Arc Exposure Test with Enhanced Light and Water Exposure for Transportation Coatings 상세보기
ASTM B487-85(2013) - Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
