관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
| 분야 | 01.09 : 비철화스너 (구름요소베어링) |
|---|---|
| 적용범위 | 1.1 This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems (the washers of screw-washer assemblies are excluded). This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of 420 MPa and higher; and inch series products with nominal diameters of No. 5 (0.1250 in.) and larger and with specified minimum tensile strengths of 60 000 psi and higher. 1.2 When the engineering requirements of the application necessitate control of surface discontinuities on bolts, screws, or studs, the purchaser shall specify conformance to ASTM Specification F788, in the original inquiry and purchase order. 1.2.1 When the engineering requirements of the application necessitate that surface discontinuities on bolts, screws, and studs be controlled within limits closer than those specified in this specification, the purchaser shall specify the applicable limits in the original inquiry and purchase order. 1.3 The allowable limits established in this specification for metric bolts, screws, and studs with nominal diameters from 4 to 24 mm inclusive, are essentially identical with requirements given in ISO 6157/I. There are no ISO standards for surface discontinuities on any inch-series products. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 21.060.10 : 볼트. 나사. 스터드 |
| 페이지수 | 6 |
| Edition | 13(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F788-20 | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series | 2020-04-01 | 표준 |
| 2 | ASTM F788-20 REDLINE | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series | 2020-04-01 | 표준 |
| 3 | ASTM F788-13(2018) | Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series | 2018-09-01 | 구판 |
| 4 | ASTM F788-13 | Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series | 2013-04-01 | 구판 |
| 5 | ASTM F788-12 | Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series | 2008-10-01 | 구판 |
관련상품이 존재하지 않습니다.
JIS Z 2243-1:2018 - Brinell hardness test -- Part 1: Test method 상세보기
JIS B 1251:2018 - Spring lock washers 상세보기
ASTM E18-19 REDLINE - Standard Test Methods for Rockwell Hardness of Metallic Materials 상세보기
ASTM E10-18 REDLINE - Standard Test Method for Brinell Hardness of Metallic Materials 상세보기
ASTM F812-12(2017) - Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
