관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard for Additive Manufacturing – Post Processing Methods – Standard Specification for Thermal Post-Processing Metal Parts Made Via Powder Bed Fusion
| 분야 | 10.04 : 전자 |
|---|---|
| 적용범위 | 1.1 This standard specifies the requirements for thermal post-processing of parts produced via metal powder bed fusion to achieve the required material properties and microstructure to meet engineering requirements. This standard is intended to be referenced by Material Part Property specifications for powder bed fusion. Currently, this standard includes thermal post-processing for the materials including titanium alloys, cobalt 28 chromium 6 molybdenum, alloy UNS N07718, alloy UNS N06625, alloy, UNS 31603 and AlSi10Mg. This specification will be updated as new powder bed fusion material heat treatments are developed. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 3 |
| Edition | 18a |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3301-18a REDLINE | Standard for Additive Manufacturing – Post Processing Methods – Standard Specification for Thermal Post-Processing Metal Parts Made Via Powder Bed Fusion | 2018-07-15 | 표준 |
| 2 | ASTM F3301-18a | Standard for Additive Manufacturing – Post Processing Methods – Standard Specification for Thermal Post-Processing Metal Parts Made Via Powder Bed Fusion | 2018-07-15 | 표준 |
| 3 | ASTM F3301-18 | Standard for Additive Manufacturing – Post Processing Methods – Standard Specification for Thermal Post-Processing Metal Parts Made Via Powder Bed Fusion | 2018-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM ISO/ASTM52910-18 - Additive manufacturing ? Design ? Requirements, guidelines and recommendations 상세보기
ASTM F3122-14 - Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes 상세보기
ASTM F3184-16 - Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion 상세보기
ASTM F3187-16 - Standard Guide for Directed Energy Deposition of Metals 상세보기
ASTM ISO/ASTM52901-16 - Standard Guide for Additive Manufacturing – General Principles – Requirements for Purchased AM Parts 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
