관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Sulfated Ash from Lubricating Oils and Additives
| 분야 | 05.01 : 석유제품 및 윤활유 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the sulfated ash from unused lubricating oils containing additives and from additive concentrates used in compounding. These additives usually contain one or more of the following metals: barium, calcium, magnesium, zinc, potassium, sodium, and tin. The elements sulfur, phosphorus, and chlorine can also be present in combined form. 1.2 Application of this test method to sulfated ash levels below 0.02 % by mass is restricted to oils containing ashless additives. The lower limit of the test method is 0.005 % by mass sulfated ash. Note 1: This test method is not intended for the analysis of used engine oils or oils containing lead. Neither is it recommended for the analysis of nonadditive lubricating oils, for which Test Method D482 can be used. Note 2: There is evidence that magnesium does not react the same as other alkali metals in this test. If magnesium additives are present, the data is interpreted with caution. Note 3: There is evidence that samples containing molybdenum can give low results because molybdenum compounds are not fully recovered at the temperature of ashing. 1.3 Fatty acid methyl ester (FAME) conforming to EN 14213 and EN 14214, when tested using this test method, were shown to meet its precision. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 75.100 : 윤활유 |
| 페이지수 | 5 |
| Edition | 13a(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D874-23 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2023-03-01 | 표준 |
| 2 | ASTM D874-23 REDLINE | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2023-03-01 | 표준 |
| 3 | ASTM D874-13a(2018) | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2018-04-01 | 구판 |
| 4 | ASTM D874-13a | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2013-09-01 | 구판 |
| 5 | ASTM D874-13 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2013-08-01 | 구판 |
| 6 | ASTM D874-07 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2007-11-01 | 구판 |
| 7 | ASTM D874-06 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2006-05-01 | 구판 |
| 8 | ASTM D874-00 | Standard Test Method for Sulfated Ash from Lubricating Oils and Additives | 2000-01-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D892-18 - Standard Test Method for Foaming Characteristics of Lubricating Oils 상세보기
ASTM D130-18 - Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test 상세보기
ASTM D1500-12(2017) - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) 상세보기
ASTM D2896-15 - Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration 상세보기
ASTM D4951-14 - Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
