관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 These test methods cover the measurement of the particle size of plastic materials in the powdered, granular, or pelleted forms in which they are commonly supplied. As these test methods utilize dry sieving, the lower limit of measurement is considered to be about 38 μm (No. 400 sieve). For smaller particle sizes, sedimentation test methods are recommended. 1.2 Two test methods are described: 1.2.1 Test Method A—This test method uses multiple sieves selected to span the particle size of the material. This method is used to determine the mean particle diameter and particle size distribution. 1.2.2 Test Method B—This test method is an abbreviated version of Test Method A conducted with a few specific sieves. This test method determines “percent passing” or “percent retained” on a given sieve. Test Method B is applicable to materials which do not have a normal particle size distribution such as pellets and cubes. 1.3 The values stated in SI units are to be regarded as standard for dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent for this test method. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 4 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1921-18 REDLINE | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2018-04-01 | 표준 |
| 2 | ASTM D1921-18 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2018-04-01 | 표준 |
| 3 | ASTM D1921-12 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2012-08-01 | 구판 |
| 4 | ASTM D1921-06e1 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2006-04-01 | 구판 |
| 5 | ASTM D1921-06 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2006-04-01 | 구판 |
| 6 | ASTM D1921-96 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2001-08-10 | 구판 |
| 7 | ASTM D1921-01 | Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials | 2001-08-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D3246-15 - Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry (Withdrawn 2024) 상세보기
ASTM D1895-17 - Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials 상세보기
ASTM D256-10(2018) - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 상세보기
ASTM E114 - 20 - Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing 상세보기
ASTM A307 - 21 - Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
