관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. Note 1: This test method and the specified reagents were specifically developed for polyethylene and polypropylene films. It is possible to utilize this test method and the specified reagents for films composed of other polymers, but this can affect the surface energies of the gas-liquid and solid-liquid interfaces, which will affect the contact angle and wetting tension. The applicability and significance for use of non-polyolefin materials must be established by the user. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 8. Note 2: This test method is equivalent to ISO 8296. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.140.10 : 필름 및 시트 |
| 페이지수 | 4 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D2578-23 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2023-02-01 | 표준 |
| 2 | ASTM D2578-23 REDLINE | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2023-02-01 | 표준 |
| 3 | ASTM D2578-17 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2017-12-15 | 구판 |
| 4 | ASTM D2578-17 REDLINE | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2017-12-15 | 구판 |
| 5 | ASTM D2578-09 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2009-09-01 | 구판 |
| 6 | ASTM D2578-08 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2008-11-01 | 구판 |
| 7 | ASTM D2578-04a | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2004-08-01 | 구판 |
| 8 | ASTM D2578-04 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 2004-02-01 | 구판 |
| 9 | ASTM D2578-99a | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films | 1999-07-10 | 구판 |
관련상품이 존재하지 않습니다.
ISO 8570:1991 - Plastics — Film and sheeting - Determination of cold-crack temperature 상세보기
ISO 4591:1992 - Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) 상세보기
ASTM D5459-95(2020) - Standard Test Method for Machine Direction Elastic Recovery and Permanent Deformation and Stress Retention of Stretch Wrap Film 상세보기
ASTM D1922-15(2020) - Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method 상세보기
ASTM D1593-19 - Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
