관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1 This practice covers suggested procedures for preparing bare, solid metal specimens for tests, for removing corrosion products after the test has been completed, and for evaluating the corrosion damage that has occurred. Emphasis is placed on procedures related to the evaluation of corrosion by mass loss and pitting measurements. (Warning—In many cases the corrosion product on the reactive metals titanium and zirconium is a hard and tightly bonded oxide that defies removal by chemical or ordinary mechanical means. In many such cases, corrosion rates are established by mass gain rather than mass loss.) 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 1.1 and 7.2. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.060 : 금속 부식 |
| 페이지수 | 9 |
| Edition | 03(2017)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G1-03(2017)e1 | Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens | 2017-11-01 | 표준 |
| 2 | ASTM G1-03(2011) | Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens | 2011-12-01 | 구판 |
| 3 | ASTM G1-03 | Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens | 2003-10-01 | 구판 |
| 4 | ASTM G1-90(1999)e1 | Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens | 1999-01-01 | 구판 |
| 5 | ASTM G1-72 | Recommended Practice for Preparing, Cleaning, And Evaluating Corrosion Test Specimens | 구판 |
관련상품이 존재하지 않습니다.
ASTM G3-14(2019) - Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing 상세보기
ASTM G46-21 - Standard Guide for Examination and Evaluation of Pitting Corrosion 상세보기
ASTM G102-89(2015)e1 - Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements 상세보기
ASTM E3-11(2017) - Standard Guide for Preparation of Metallographic Specimens 상세보기
ASTM G161-00(2018) - Standard Guide for Corrosion-Related Failure Analysis 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
