관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength
| 분야 | 01.04 : 철강-구조물, 보강재, 압력용기, 철도 | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 This specification2 covers carbon steel plates of low- and intermediate-tensile strengths which may be killed or semi-killed at the producer’s option. These plates are intended for fusion-welded pressure vessels. 1.2 Plates under this specification are available in three grades having different strength levels as follows:
1.3 The maximum thickness of plates is limited by the capacity of the composition to meet the specified mechanical property requirements. Note 1: For killed carbon steels only, refer to the following ASTM specifications:3 A299/A299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon A515/A515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service 1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
| 국제분류(ICS)코드 | 77.140.50 : 보통 강제품 및 반제품 | ||||||||
| 페이지수 | 3 | ||||||||
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A285/A285M-24 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2024-10-15 | 표준 |
| 2 | ASTM A285/A285M-24 REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2024-10-15 | 표준 |
| 3 | ASTM A285/A285M-17 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2017-11-01 | 구판 |
| 4 | ASTM A285/A285M-17 REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2017-11-01 | 구판 |
| 5 | ASTM A285/A285M-12 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2012-05-01 | 구판 |
| 6 | ASTM A285/A285M-03(2007) | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2007-11-01 | 구판 |
| 7 | ASTM A285/A285M-03 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2003-09-10 | 구판 |
| 8 | ASTM A285/A285M-90(2001) | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2001-09-10 | 구판 |
| 9 | ASTM A285/A285M-90(1996)e1 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2001-09-10 | 구판 |
| 10 | ASTM A285/A285M-01 | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength | 2001-09-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D3035-15 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter 상세보기
ASTM A387/A387M-17a - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum 상세보기
ASTM A515/A515M-17 - Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service 상세보기
ASTM C533-17 - Standard Specification for Calcium Silicate Block and Pipe Thermal Insulation 상세보기
ASTM C33/C33M-18 - Standard Specification for Concrete Aggregates 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
