관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
절판(중지)
Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates
| 언어 | 제공형태 | 판매가격 | 선택 |
|---|---|---|---|
|
영어 |
|
128,900원 |
|
|
영어 |
|
128,900원 |
|
| 분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
|---|---|
| 적용범위 | 1.1 This practice provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and compressive strengths. The composite material forms are limited to continuous-fiber reinforced polymer matrix composites in which the laminate is both symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1. 1.2 This practice supplements Test Methods D5766/D5766M (for tension testing) and D6484/D6484M (for compression testing) with provisions for testing specimens that contain a close-tolerance fastener or pin installed in the hole. Several important test specimen parameters (for example, fastener selection, fastener installation method, and fastener hole tolerance) are not mandated by this practice; however, repeatable results require that these parameters be specified and reported. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1 Within the text the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 8 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6742/D6742M-23 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2023-09-01 | 표준 |
| 2 | ASTM D6742/D6742M-17 REDLINE | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2017-10-15 | 구판 |
| 3 | ASTM D6742/D6742M-12 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2012-04-01 | 구판 |
| 4 | ASTM D6742/D6742M-07 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2007-10-15 | 구판 |
| 5 | ASTM D6742/D6742M-02(2007) | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2007-05-01 | 구판 |
| 6 | ASTM D6742/D6742M-02 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2002-10-10 | 구판 |
| 7 | ASTM D6742/D6742M-01 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2001-11-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D7136/D7136M-15 - Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event 상세보기
ASTM D6484/D6484M-14 - Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates 상세보기
ASTM D2344/D2344M-16 - Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates 상세보기
ASTM D6641/D6641M-16e1 - Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture 상세보기
ASTM D7137/D7137M-17 - Standard Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
