관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
---|---|
적용범위 | 1.1 This practice provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and compressive strengths. The composite material forms are limited to continuous-fiber reinforced polymer matrix composites in which the laminate is both symmetric and balanced with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1. 1.2 This practice supplements Test Methods (for tension testing) and D6484/D6484M (for compression testing) with provisions for testing specimens that contain a close-tolerance fastener or pin installed in the hole. Several important test specimen parameters (for example, fastener selection, fastener installation method, and fastener hole tolerance) are not mandated by this practice; however, repeatable results require that these parameters be specified and reported. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3.1 Within the text the inch-pound units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
국제분류(ICS)코드 | |
페이지수 | 8 |
Edition | 12 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D6742/D6742M-23 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2023-09-01 | 표준 |
2 | ASTM D6742/D6742M-17 REDLINE | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2017-10-15 | 구판 |
3 | ASTM D6742/D6742M-12 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2012-04-01 | 구판 |
4 | ASTM D6742/D6742M-07 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2007-10-15 | 구판 |
5 | ASTM D6742/D6742M-02(2007) | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2007-05-01 | 구판 |
6 | ASTM D6742/D6742M-02 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2002-10-10 | 구판 |
7 | ASTM D6742/D6742M-01 | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates | 2001-11-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기