관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
| 분야 | 01.06 : 피복 철강 제품 | |||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1. TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass] Note 1: Listed below are the commonly produced coating weights [mass] upon agreement between the producer and the purchaser. Other combinations of coatings may be specified and the appropriate minimum average test valuesA apply.
(A) Refer to Specifications A623 and A623M. (B) A base box is defined as a unit of area equivalent to 112 sheets 14 in. by 20 in. or 31 360 in.2 (refer to Specification A623). (C) The minimum single spot value shall not be less than 80 % of the minimum average tin coating weight [mass] (see 8.1 and 8.2). 1.1.1 Electrolytic tin-coated sheet is customarily available as commercial steel (CS); drawing steel (DS); deep drawing steel (DDS); extra deep drawing steel (EDDS), and structural steel (SS). The tin coating is available as unmelted or melted. 1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M]. 1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
|||||||||||||||||||||||||||
| 국제분류(ICS)코드 | 77.140.50 : 보통 강제품 및 반제품 | |||||||||||||||||||||||||||
| 페이지수 | 3 | |||||||||||||||||||||||||||
| Edition | 07(2017) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A599/A599M-07(2017) | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet | 2017-09-01 | 표준 |
| 2 | ASTM A599/A599M-07(2012) | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet | 2012-03-01 | 구판 |
| 3 | ASTM A599/A599M-07 | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet | 2007-11-01 | 구판 |
| 4 | ASTM A599/A599M-02 | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet | 2002-09-10 | 구판 |
| 5 | ASTM A599/A599M-99 | Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet | 1999-09-10 | 구판 |
관련상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
