관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
| 분야 | 04.11 : 건축 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers testing procedures for architectural joint systems. This test method is intended for the following uses for architectural joint systems: 1.1.1 To verify movement capability information supplied to the user by the producer, 1.1.2 To standardize comparison of movement capability by relating it to specified nominal joint widths, 1.1.3 To determine the cyclic movement capability between specified minimum and maximum joint widths without visual deleterious effects, and 1.1.4 To provide the user with graphic information, drawings or pictures in the test report, depicting them at minimum, maximum, and nominal joint widths during cycling. 1.2 This test method is intended to be used only as part of a specification or acceptance criterion due to the limited movements tested. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.080.40 : 콘크리트 구조물 |
| 페이지수 | 6 |
| Edition | 97(2017) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1399/E1399M-97(2022) | Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems | 2022-10-01 | 표준 |
| 2 | ASTM E1399/E1399M-97(2017) | Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems | 2017-09-01 | 구판 |
| 3 | ASTM E1399/E1399M-97(2013)e1 | Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems | 2013-09-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E90-09(2016) - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements 상세보기
ASTM E814-13a(2017) - Standard Test Method for Fire Tests of Penetration Firestop Systems 상세보기
ASTM E1966-15(2019) - Standard Test Method for Fire-Resistive Joint Systems 상세보기
ASTM E2307-19 - Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus 상세보기
ASTM E3038-16 - Standard Practice for Assessing and Qualifying Candidates as Inspectors of Firestop Systems and Fire-Resistive Joint Systems 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
