관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
| 분야 | 07.02 : 섬유 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing. 1.1.1 The grab test procedure is applicable to woven, nonwoven, and felted fabrics, while the modified grab test procedure is used primarily for woven fabrics. 1.2 This test method is not recommended for glass fabrics, or for knitted fabrics and other textile fabrics which have high stretch (more than 11 %). Note 1: For the determination of the breaking force and elongation of textile fabrics using the raveled strip test procedure and the cut strip test procedure, refer to Test Method D5035. 1.3 This test method provides the values in both inch-pound units and SI units. Inch-pound units is the technically correct name for the customary units used in the United States. SI units is the technically correct name for the system of metric units known as the International System of Units. The values stated in either acceptable metric units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining in any way. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 59.080.30 : 직물류 |
| 페이지수 | 8 |
| Edition | 09(2017) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5034-21 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2021-02-15 | 표준 |
| 2 | ASTM D5034-21 REDLINE | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2021-02-15 | 표준 |
| 3 | ASTM D5034-09(2017) | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2017-07-15 | 구판 |
| 4 | ASTM D5034-09(2013) | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2013-07-01 | 구판 |
| 5 | ASTM D5034-09 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2009-01-15 | 구판 |
| 6 | ASTM D5034-08 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 2008-06-01 | 구판 |
| 7 | ASTM D5034-95 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 1995-05-15 | 구판 |
| 8 | ASTM D5034-95(2001) | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) | 1995-05-15 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D737-18 - Standard Test Method for Air Permeability of Textile Fabrics 상세보기
ASTM D3775-17e1 - Standard Test Method for End (Warp) and Pick (Filling) Count of Woven Fabrics 상세보기
ASTM D3776/D3776M-09a(2017) - Standard Test Methods for Mass Per Unit Area (Weight) of Fabric 상세보기
ASTM D3774-18 - Standard Test Method for Width of Textile Fabric 상세보기
ASTM D2261-13(2017)e1 - Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
