ASTM D1000-17 Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications

관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.

PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)

PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

구판 판매

ASTM D1000-17

Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications

- 발행일 : 2017-07-01
- 발행기관 : ASTM

언어	제공형태	판매가격	선택
영어	PDF	141,300원
영어	PRINT	141,300원

장바구니 담기

상품이 장바구니에 담겼습니다.

장바구니로 이동

상세정보

분야

10.01 : 전기절연 (Ⅰ)

적용범위

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:

1.1.1 Class 1—Non-elastomeric backings made from materials such as:

	Paper, flat or creped,
	Fabric, uncoated or coated,
	Cellulose ester films,
	Polyethylene terephthalate (polyester) films,
	Fluorocarbon polymer films,
	Composite filament films,
	Polyamide films,
	Polyimide films, and
	Combinations thereof.

1.1.2 Class 2—Elastomeric backings that are characterized by both high stretch and substantial recovery. These backings are made from materials such as:

	Vinyl chloride and co-polymers,
	Vinylidene chloride and co-polymers, and
	Polyethylene and co-polymers.

1.2 Test laminates of Class 1 and Class 2 backings according to Class 1 test methods.

1.3 The procedures appear in the sections indicated below and in alphabetical order:

Adhesion Strength to Steel and Backing at Room Temperature	46 – 53
Adhesion Strength to Steel and Backing at Low Temperatures	46 – 53
Bond Strength After Solvent Immersion	110 – 115
Breaking Strength and Elongation at Room Temperature	37 – 45
Breaking Strength and Elongation at Low Temperatures	37 – 45
Conditioning	6 – 8
Curling and Twisting	140 – 146
Dielectric Breakdown Voltage	83 – 90
Effect of Accelerated Aging on High-Temperature Tapes	97 – 103
Flagging	66 – 76
Flammability	104 – 109
Hazards/Precautions	3
Insulation Resistance at High Humidity	91 – 96
Length of Tape in a Roll	28 – 36
Oil Resistance	116 – 122
Puncture Resistance	123 – 128
Resistance to Accelerated Aging (Heat and Moisture)	129 – 139
Sampling	4
Specimen Preparation	5
Thermosetting Properties	77 – 82
Thickness	21 – 27
Unwind Force at Room Temperature	54 – 65
Unwind Force at Low Temperatures	54 – 65
Width	11 – 20

Note 1: These procedures apply to both Class 1 and Class 2 tapes except as noted above.

1.4 This is a fire-test response standard (see Section 104).

1.5 The values stated in SI units are the standard, unless otherwise noted. If a value for measurement is followed by a value in inch-pound or English units in parentheses, it is likely that the second value will only be approximate and it is for information only. The first stated value is the preferred unit.

Note 2: These test methods are similar to IEC 60454–3, but may differ sometimes in some details.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 3.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드

29.035.20 : 유리 및 세라믹 절연 재료

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM D1000-24	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2024-09-01	표준
2	ASTM D1000-24 REDLINE	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2024-09-01	표준
3	ASTM D1000-17 REDLINE	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2017-07-01	구판
4	ASTM D1000-17	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2017-07-01	구판
5	ASTM D1000-10	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2010-01-01	구판
6	ASTM D1000-09	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2009-10-15	구판
7	ASTM D1000-04e1	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2004-09-01	구판
8	ASTM D1000-04	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2004-09-01	구판
9	ASTM D1000-99	Standard Test Method for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	1999-03-10	구판

관련상품

관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품

FORD WSS-M18P11-B . 2022 Edition, June 20, 2022 - SEALER, HIGH HEAT EXPANSION PERFORMANCE REQUIREMENT, HEAT CURING 상세보기

ASTM B265-20a - Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate 상세보기

ASTM D6818-18a - Standard Test Method for Ultimate Tensile Properties of Rolled Erosion Control Products 상세보기

ASTM D3574-95 - Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams 상세보기

FORD WSS-M2G575-A .2016 Edition, October 18, 2016 - ADHESIVE, EPOXY, WELDABLE, THERMAL CURE, STRUCTURAL, HEM FLANGE 상세보기
추천 상품

IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기

IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기

KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기

KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기

KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기

해외표준

ASTM D1000-17

상세정보

이력정보

관련상품

다른 사람이 함께 구입한 상품

추천 상품

전체서비스 보기