ASTM C494/C494M-17 Standard Specification for Chemical Admixtures for Concrete

관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.

PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)

PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

구판 판매

ASTM C494/C494M-17

Standard Specification for Chemical Admixtures for Concrete

- 발행일 : 2017-06-15
- 발행기관 : ASTM

언어	제공형태	판매가격	선택
영어	PDF	128,900원
영어	PRINT	128,900원

장바구니 담기

상품이 장바구니에 담겼습니다.

장바구니로 이동

상세정보

분야

04.02 : 콘크리트 및 골재

적용범위

1.1 This specification covers materials for use as chemical admixtures to be added to hydraulic-cement concrete mixtures in the field for the purpose or purposes indicated for the eight types as follows:

1.1.1 Type A—Water-reducing admixtures,

1.1.2 Type B—Retarding admixtures,

1.1.3 Type C—Accelerating admixtures,

1.1.4 Type D—Water-reducing and retarding admixtures,

1.1.5 Type E—Water-reducing and accelerating admixtures,

1.1.6 Type F—Water-reducing, high range admixtures,

1.1.7 Type G—Water-reducing, high range, and retarding admixtures, and

1.1.8 Type S—Specific performance admixtures.

1.2 This specification stipulates tests of an admixture with suitable concreting materials as described in 11.1 – 11.3 or with cement, pozzolan, aggregates, and an air-entraining admixture proposed for specific work (11.4). Unless specified otherwise by the purchaser, the tests shall be made using concreting materials as described in 11.1 – 11.3.

Note 1: It is recommended that, whenever practicable, tests be made using the cement, pozzolan, aggregates, air-entraining admixture, and the mixture proportions, batching sequence, and other physical conditions proposed for the specific work (11.4) because the specific effects produced by chemical admixtures may vary with the properties and proportions of the other ingredients of the concrete. For instance, Types F and G admixtures may exhibit much higher water reduction in concrete mixtures having higher cement factors than that listed in 12.1.1.

Mixtures having a high range water reduction generally display a higher rate of slump loss. When high-range admixtures are used to impart increased workability (6 to 8-in. slump [150 to 200–mm]), the effect may be of limited duration, reverting to the original slump in 30 to 60 min depending on factors normally affecting rate of slump loss. The use of chemical admixtures to produce high-slump (flowing) concrete is covered by Specification C1017/C1017M.

Note 2: The purchaser should ensure that the admixture supplied for use in the work is equivalent in composition to the admixture subjected to test under this specification (see Section 6, Uniformity and Equivalence).

Note 3: Admixtures that contain relatively large amounts of chloride may accelerate corrosion of prestressing steel. Compliance with the requirements of this specification does not constitute assurance of acceptability of the admixture for use in prestressed concrete.

1.3 This specification provides for three levels of testing.

1.3.1 Level 1—During the initial approval stage, proof of compliance with the performance requirements defined in Table 1 demonstrates that the admixture meets the requirements of this specification. Admixtures (except for Types B, C, E, and S) shall qualify for provisional compliance when the physical requirements and any of the alternative compressive strength requirements in Table 1 are met. If subsequent test results at six months or one year fail to meet the standard requirement of 100 % of reference strength, the compliance of the admixture to this standard is withdrawn and all users of the admixture shall be notified immediately. Uniformity and equivalence tests of Section 6 shall be carried out to provide results against which later comparisons can be made (see Note 4).

TABLE 1 Physical Requirements^A

	Type A, Water Reducing	Type B, Retarding	Type C, Acceler- ating	Type D, Water Reducing and Retarding	Type E, Water Reducing and Accelerating	Type F, Water Reducing, High Range	Type G, Water Reducing, High Range and Retarding	Type S Specific Performance
Water content, max, % of control	95	...	...	95	95	88	88	...
Time of setting, allowable deviation from control, h:min:
Initial: at least	...	1:00 later	1:00 earlier	1:00 later	1:00 earlier	...	1:00 later
not more than	1:00 earlier nor 1:30 later	3:30 later	3:30 earlier	3:30 later	3:30 earlier	1:00 earlier nor 1:30 later	3:30 later	1:00 earlier nor 1:30 later
Final: at least	...	...	1:00 earlier	...	1:00 earlier	...	...
not more than	1:00 earlier nor 1:30 later	3:30 later	...	3:30 later	...	1:00 earlier nor 1:30 later	3:30 later	1:00 earlier nor 1:30 later
Compressive strength, min, % of control:^B
1 day	...	...	...	...	...	140	125	...
3 days	110	90	125	110	125	125	125	90
7 days	110	90	100	110	110	115	115	90
28 days	110 (120)^C	90	100	110 (120)^C	110	110 (120)^C	110 (120)^C	90
90 days	(117)^C	n/a	n/a	(117)^C	n/a	(117)^C	(117)^C	n/a
6 months	100 (113)^C	90	90	100 (113)^C	100	100 (113)^C	100 (113)^C	90
1 year	100	90	90	100	100	100	100	90
Flexural strength, min, % control:^B
3 days	100	90	110	100	110	110	110	90
7 days	100	90	100	100	100	100	100	90
28 days	100	90	90	100	100	100	100	90
Length change, max shrinkage (alternative requirements):^D
Percent of control	135	135	135	135	135	135	135	135
Increase over control	0.010	0.010	0.010	0.010	0.010	0.010	0.010	0.010
Relative durability factor, min^E	80	80	80	80	80	80	80	80

(A) The values in the table include allowance for normal variation in test results. The object of the 90 % compressive strength requirement for a Type B amd Type S admixture is to require a level of performance comparable to that of the reference concrete.

(B) The compressive and flexural strength of the concrete containing the admixture under test at any test age shall be not less than 90 % of that attained at any previous test age. The objective of this limit is to require that the compressive or flexural strength of the concrete containing the admixture under test shall not decrease with age.

국제분류(ICS)코드

91.100.30 : 콘크리트 및 콘크리트 제품

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM C494/C494M-24	Standard Specification for Chemical Admixtures for Concrete	2024-06-15	표준
2	ASTM C494/C494M-24 REDLINE	Standard Specification for Chemical Admixtures for Concrete	2024-06-15	표준
3	ASTM C494/C494M-19	Standard Specification for Chemical Admixtures for Concrete	2019-12-15	구판
4	ASTM C494/C494M-19 REDLINE	Standard Specification for Chemical Admixtures for Concrete	2019-12-15	구판
5	ASTM C494/C494M-19e1	Standard Specification for Chemical Admixtures for Concrete	2019-12-15	구판
6	ASTM C494/C494M-17	Standard Specification for Chemical Admixtures for Concrete	2017-06-15	구판
7	ASTM C494/C494M-17 REDLINE	Standard Specification for Chemical Admixtures for Concrete	2017-06-15	구판
8	ASTM C494/C494M-16	Standard Specification for Chemical Admixtures for Concrete	2016-07-01	구판
9	ASTM C494/C494M-15a	Standard Specification for Chemical Admixtures for Concrete	2015-10-01	구판
10	ASTM C494/C494M-15	Standard Specification for Chemical Admixtures for Concrete	2015-06-15	구판
11	ASTM C494/C494M-13	Standard Specification for Chemical Admixtures for Concrete	2013-04-01	구판
12	ASTM C494/C494M-12	Standard Specification for Chemical Admixtures for Concrete	2012-07-01	구판
13	ASTM C494/C494M-11	Standard Specification for Chemical Admixtures for Concrete	2011-07-01	구판
14	ASTM C494/C494M-10a	Standard Specification for Chemical Admixtures for Concrete	2010-10-01	구판
15	ASTM C494/C494M-10	Standard Specification for Chemical Admixtures for Concrete	2010-02-01	구판
16	ASTM C494/C494M-08a	Standard Specification for Chemical Admixtures for Concrete	2008-09-01	구판
17	ASTM C494/C494M-08	Standard Specification for Chemical Admixtures for Concrete	2008-01-01	구판
18	ASTM C494/C494M-05a	Standard Specification for Chemical Admixtures for Concrete	2005-12-15	구판
19	ASTM C494/C494M-05	Standard Specification for Chemical Admixtures for Concrete	2005-05-01	구판
20	ASTM C494/C494M-04	Standard Specification for Chemical Admixtures for Concrete	2004-01-01	구판
21	ASTM C494/C494M-99a	Standard Specification for Chemical Admixtures for Concrete	1999-10-10	구판
22	ASTM C494/C494M-99ae1	Standard Specification for Chemical Admixtures for Concrete	1999-10-10	구판

관련상품

관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품

ASTM D2412-11(2018) - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading 상세보기

IEC TR 61850-90-6:2018 - Communication networks and systems for power utility automation - Part 90-6: Use of IEC 61850 for Distribution Automation Systems 상세보기

IEC 61850-6:2009 - Communication networks and systems for power utility automation - Part 6: Configuration description language for communication in electrical substations related to IEDs 상세보기

ASME B30.16 - 2017 - Overhead Underhung and Stationary Hoists 상세보기

ASTM D2049 1969 Edition - Test Method for Relative Density of Cohesionless Soils 상세보기
추천 상품

IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기

IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기

KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기

KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기

KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기

해외표준

ASTM C494/C494M-17

상세정보

이력정보

관련상품

다른 사람이 함께 구입한 상품

추천 상품

전체서비스 보기