관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart. This energy is expressed in terms of the weight (mass) of the missile falling from a specified height which would result in 50 % failure of specimens tested. 1.2 Two test methods are described: 1.2.1 Test Method A employs a dart with a 38.10 ± 0.13-mm (1.500 ± 0.005-in.) diameter hemispherical head dropped from a height of 0.66 ± 0.01 m (26.0 ± 0.4 in.). This test method can be used for films whose impact resistances require masses of about 50 g or less to about 6 kg to fracture them. 1.2.2 Test Method B employs a dart with a 50.80 ± 0.13-mm (2.000 ± 0.005-in.) diameter hemispherical head dropped from a height of 1.52 ± 0.03 m (60.0 + 0.25, −1.70 in.). Its range of applicability is from about 0.3 kg to about 6 kg. 1.3 Two testing techniques are described: 1.3.1 The standard technique is the staircase method. By this technique, the missile weight employed during the test is decreased or increased by uniform increments after the testing of each specimen, depending upon the result (fail or not fail) observed for the specimen. 1.3.2 The alternative technique provides for testing specimens in successive groups of ten. One missile weight is employed for each group and the missile weight is varied in uniform increments from group to group. 1.3.3 The staircase technique and the alternative technique give equivalent results both as to the values of impact failure weight which are obtained and as to the precisions with which they are determined. 1.4 The values stated in SI units are to be regarded as standard. The values stated in parentheses are for information only. Note 1: Tests on materials that do not break, for any reason, are not considered to be valid. It has been noted that certain materials may stretch so far as to bottom out at the base of certain test instruments without actually rupturing. Subcommittee D20.19 is currently considering methods for testing these materials. Anyone interested in participating in a Task Group should contact the Chairman of Subcommittee D20.19 through ASTM International Headquarters. 1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2: Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.). Note 3: This test method is technically equivalent to ISO 7765-1: 1988, with the exception of a larger tolerance on the drop height in Test Method B, smaller tolerances on the dart diameters for Test Methods A and B, and the requirement for a vented dart well in 5.1.1. Also, the ISO method does not allow the alternative testing technique described in Section 11 of this test method. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.140.10 : 필름 및 시트 |
| 페이지수 | 10 |
| Edition | 16ae1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1709-24 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2024-09-01 | 표준 |
| 2 | ASTM D1709-22 REDLINE | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2022-07-01 | 구판 |
| 3 | ASTM D1709-16ae1 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2016-05-01 | 구판 |
| 4 | ASTM D1709-16a | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2016-05-01 | 구판 |
| 5 | ASTM D1709-16 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2016-04-15 | 구판 |
| 6 | ASTM D1709-15a | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2015-05-15 | 구판 |
| 7 | ASTM D1709-15 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2015-01-01 | 구판 |
| 8 | ASTM D1709-09 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2009-05-01 | 구판 |
| 9 | ASTM D1709-08 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2008-11-01 | 구판 |
| 10 | ASTM D1709-04 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2004-10-01 | 구판 |
| 11 | ASTM D1709-03 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2003-03-10 | 구판 |
| 12 | ASTM D1709-98 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2001-08-10 | 구판 |
| 13 | ASTM D1709-01 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method | 2001-08-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D651(1984 Edition) - STANDARD TEST METHOD FOR TENSILE STRENGTH OF MOLDED ELECTRICAL INSULATING MATERIALS 상세보기
ASTM D3431(1987 Edition) - STANDARD TEST METHOD FOR TRACE NITROGEN IN LIQUID PETROLEUM HYDROCARBONS (MICROCOULOMETRIC METHOD) 상세보기
ASTM D3416(1988 Edition) - STANDARD TEST METHOD FOR TOTAL HYDROCARBONS, METHANE, AND CARBON MONOXIDE IN THE ATMOSPHERE (GAS CHROMATOGRAPHIC METHOD) 상세보기
ASTM D2725(87th Edition) - Standard Test Method for Hydrogen Sulfide in Natural Gas (Methylene Blue Method) 상세보기
ASTM D1835-20 - Standard Specification for Liquefied Petroleum (LP) Gases 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
