ASTM E3061-17 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method)

관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.

PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)

PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

구판 판매

ASTM E3061-17

Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method)

- 발행일 : 2017-01-15
- 발행기관 : ASTM

언어	제공형태	판매가격	선택
영어	PDF	140,700원
영어	PRINT	140,700원

장바구니 담기

상품이 장바구니에 담겼습니다.

장바구니로 이동

상세정보

분야

03.05 : 금속, 광석 및 관련 재료의 분석화학

적용범위

1.1 This test method describes the inductively coupled plasma atomic emission spectrometric analysis of aluminum and aluminum alloys for the following elements:

Elements	Application Range, %
Elements	Minimum	Maximum
Si	0.02	16.8
Fe	0.02	3.06
Cu	0.005	7.0
Mn	0.003	1.41
Mg	0.006	8.2
Cr	0.004	0.52
Ni	0.004	2.71
Zn	0.02	9.65
Ti	0.009	0.20
Ag	0.003	0.4
As	0.005	0.012
B	0.009	0.027
Ba	0.002	0.03
Be	0.002	0.11
Bi	0.01	0.59
Ca	0.003	0.048
Cd	0.002	0.055
Co	0.002	0.034
Ga	0.01	0.019
Li	0.001	2.48
Mo	0.02	0.15
Na	0.008	0.026
P	0.01	0.025
Pb	0.009	0.51
Sb	0.01	0.28
Sc	0.01	0.065
Sn	0.008	6.28
Sr	0.0008	0.028
Ti	0.005	0.20
Tl	0.009	0.13
V	0.01	0.12
Zr	0.004	0.25

1.2 This test method has only been interlaboratory tested for the elements and ranges specified. It may be possible to extend this test method to other elements or different composition ranges if method validation, which includes evaluation of method sensitivity and precision and bias (as described in Section 14), is performed. Additionally, the validation study must evaluate the acceptability of sample preparation methodology using reference materials and/or spike recoveries. The user should carefully evaluate the validation data against the laboratory’s data quality objectives. Method validation of scope extensions is also a requirement of ISO/IEC 17025.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Safety hazard statements are given in Section 10 and specific warning statements are given in Sections 15, 17, 18, 19, 20 and 21.

국제분류(ICS)코드

77.040.30 : 금속 조직학 및 기타 시험방법
77.120.10 : 알루미늄 및 알루미늄합금

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM E3061-24	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based)	2024-05-15	표준
2	ASTM E3061-24 REDLINE	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based)	2024-05-15	표준
3	ASTM E3061-17	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method)	2017-01-15	구판

관련상품

관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품

ASTM A568/A568M-19a - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for 상세보기

ASTM E446-15 - Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness 상세보기

ASTM A749/A749M-14 - Standard Specification for Steel, Strip, Carbon and High-Strength, Low-Alloy, Hot-Rolled, General Requirements for 상세보기

VDA 230-213 Testing procedure for product classes Prelube, Prelube 2, Hotmelt, Spot lubricant - 상세보기

GB/T 5313-2010 - Steel plates with through-thickness characteristics 상세보기
추천 상품

IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기

IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기

KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기

KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기

KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기

해외표준

ASTM E3061-17

상세정보

이력정보

관련상품

다른 사람이 함께 구입한 상품

추천 상품

전체서비스 보기