관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements
| 분야 | 01.05 : 철강-환봉, 단조품, 베어링, 체인, 스프링 |
|---|---|
| 적용범위 | 1.1 This specification2 covers heat-treated carbon steel and alloy steel forgings with mandatory toughness requirements. These forgings are intended for pressure vessels, feedwater heaters, and similar uses. 1.2 These forgings include tube sheets, covers, channel barrels, integral forged channels, rings, nozzles, flanges, and similar parts. 1.3 All grades are considered weldable under proper conditions. 1.4 The maximum thickness of forgings produced to this specification is limited only by the capacity of the selected grade to respond to any heat treatment specified and to meet the specified mechanical tests, including impact tests at the specified temperature. 1.5 Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlines additional ordering information, manufacturing requirements, testing and retesting methods and procedures, marking, certification, product analysis variations, and additional supplementary requirements. 1.6 If the requirements of this specification are in conflict with the requirements of Specification A788/A788M, the requirements of this specification shall prevail. 1.7 The values stated in either inch-pound units or SI [metric] units are to be regarded separately as the standard; within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.8 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units. |
| 국제분류(ICS)코드 | 77.140.30 : 압력용기용 강 |
| 페이지수 | 4 |
| Edition | 07(2017) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A765/A765M-24 | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2024-08-15 | 표준 |
| 2 | ASTM A765/A765M-24 REDLINE | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2024-08-15 | 표준 |
| 3 | ASTM A765/A765M-07(2022) | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2022-09-01 | 구판 |
| 4 | ASTM A765/A765M-07(2017) | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2017-03-15 | 구판 |
| 5 | ASTM A765/A765M-07(2012) | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2012-05-01 | 구판 |
| 6 | ASTM A765/A765M-07 | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2007-09-01 | 구판 |
| 7 | ASTM A765/A765M-04 | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2004-07-01 | 구판 |
| 8 | ASTM A765/A765M-98a | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2001-10-10 | 구판 |
| 9 | ASTM A765/A765M-01 | Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements | 2001-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A537/A537M-20 - Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel 상세보기
ASTM E1010-16 - Standard Practice for Preparation of Disk Specimens of Steel and Iron by Remelting for Spectrochemical Analysis (Withdrawn 2022) 상세보기
ASTM A361-76(1981)e1 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) By The Hot-Dip Process For Roofing And Siding 상세보기
GB/T 224-2019 - Determination of the depth of decarburization of steels 상세보기
GB/T 6394-2017 - Determination of estimating the average grain size of metal 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
