관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Ultrasonic Testing of Wrought Products
| 분야 | 03.04 : 비 파괴검사 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 Purpose—This practice establishes the minimum requirements for ultrasonic examination of wrought products. Note 1: This standard was adopted to replace MIL-STD-2154, 30 Sept. 1982. This standard is intended to be used for the same applications as the document which it replaced. Users should carefully review its requirements when considering its use for new, or different applications, or both. 1.2 Application—This practice is applicable for examination of materials such as, wrought metals and wrought metal products having a thickness or cross section equal to 0.250 in. (6.35 mm) or greater. 1.2.1 Wrought Aluminum Alloy Products—Examination shall be in accordance with Practice B594. 1.3 Acceptance Class—When examination is performed in accordance with this practice, engineering drawings, specifications, or other applicable documents shall indicate the acceptance criteria. Five ultrasonic acceptance classes are defined in Table 1. One or more of these classes may be used to establish the acceptance criteria or additional or alternate criteria may be specified. (A) Any discontinuity with a response greater than the response from a flat-bottom hole or equivalent notch (see footnote B) at the estimated discontinuity depth and the discontinuity size given is not acceptable. (B) See Fig. 3, Fig. 4, or Fig. 5 for dimensions of notches and holes when these are required for angle beam examination of tube walls and near-surface regions of cylindrical parts and other products. (C) Multiple discontinuities with indications greater than the response from a reference flat-bottom hole or equivalent notch at the estimated discontinuity depth of the size given (diameter) are not acceptable if the centers of any two of these discontinuities are less than one inch apart (not applicable to Class C). (D) Any discontinuity longer than the length given with indications equal to or greater than the response given (flat-bottom hole or notch response) is not acceptable. Not applicable to Class C). (E) Loss of back reflection by more than 50 %, when compared to non-defective material in the same or a similar part, is not acceptable. (F) For longitudinal examination of material over 6-in. (152.4-mm) thick in the short transverse direction, any loss of back reflection equal to or greater than 12 dB over an area 2 by 2 in. (50.8 by 50.8 mm) is rejectable. (Noise level is not relevant to this back reflection evaluation. (G) Noise which exceeds the alarm level setting (see 7.4.10.7), is not acceptable, except for titanium. For titanium alloys, the alarm level may be set just above the noise level, but shall not exceed 70 % of the reference standard response. (H) When examining titanium, Class AA and Class AAA, no rejection shall be made on the basis of “noise” level, if within the limits specified in footnote G. (I) Evaluation may be done by setting up on a 3/64 in. (1.19 mm) hole and adding 7 dB of gain. (Also see Note 5 under Table 5.) 1.4 Order of Precedence—Contractual requirements and authorized direction from the cognizant engineering organization may add to or modify the requirements of this practice. Otherwise, in the event of conflict between the text of this practice and the references cited herein, the text of this practice takes precedence. Nothing in this practice, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1.5 Measurement Values—The values stated in inch-pounds are to be regarded as standard. The metric equivalents are in parentheses. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 71.040.99 : 화학 분석 관련 기타 표준 |
| 페이지수 | 24 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2375-22 | Standard Practice for Ultrasonic Testing of Wrought Products | 2022-12-01 | 표준 |
| 2 | ASTM E2375-22 REDLINE | Standard Practice for Ultrasonic Testing of Wrought Products | 2022-12-01 | 표준 |
| 3 | ASTM E2375-16 | Standard Practice for Ultrasonic Testing of Wrought Products | 2016-12-01 | 구판 |
| 4 | ASTM E2375-16 REDLINE | Standard Practice for Ultrasonic Testing of Wrought Products | 2016-12-01 | 구판 |
| 5 | ASTM E2375-08(2013) | Standard Practice for Ultrasonic Testing of Wrought Products | 2013-06-01 | 구판 |
| 6 | ASTM E2375-08 | Standard Practice for Ultrasonic Testing of Wrought Products | 2008-02-01 | 구판 |
| 7 | ASTM E2375-04 | Standard Practice for Ultrasonic Examination of Wrought Products | 2004-07-01 | 구판 |
관련상품이 존재하지 않습니다.
DIN EN 2032-2:1994-05 - Aerospace series; metallic materials; part 2: coding of metallurgical condition in delivery condition; German version EN 2032-2:1994 상세보기
DIN EN 2004-1:1993-09 - Aerospace series; test methods for aluminium and aluminium alloy products; part 1: determination of electrical conductivity of wrought aluminium alloys; German version EN 2004-1:1993 상세보기
DIN EN 2002-7:1999-05 - Aerospace series - Metallic materials; test methods - Part 7: Hardness test 상세보기
BS EN 2002-1:2005 - Aerospace series. Metallic materials. Test methods. Tensile testing at ambient temperature. 상세보기
ASTM B918/B918M-20a - Standard Practice for Heat Treatment of Wrought Aluminum Alloys 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
