관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Flash Point by Tag Closed Cup Tester
| 분야 | 05.01 : 석유제품 및 윤활유 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the flash point, by tag manual and automated closed testers, of liquids with a viscosity below 5.5 mm2/s (cSt) at 40 °C (104 °F), or below 9.5 mm2/s (cSt) at 25 °C (77 °F), and a flash point below 93 °C (200 °F). 1.1.1 For the closed-cup flash point of liquids with the following properties: a viscosity of 5.5 mm2/s (cSt) or more at 40 °C (104 °F); a viscosity of 9.5 mm2/s (cSt) or more at 25 °C (77 °F); a flash point of 93 °C (200 °F) or higher; a tendency to form a surface film under test conditions; or containing suspended solids, Test Method D93 can be used. 1.1.2 For cut-back asphalts refer to Test Methods D1310 and D3143. Note 1: The U.S. Department of Transportation (RSTA)2 and U.S. Department of Labor (OSHA) have established that liquids with a flash point under 37.8 °C (100 °F) are flammable as determined by this test method for those liquids that have a viscosity less than 5.5 mm2/s (cSt) at 40 °C (104 °F) or 9.5 mm2/s (cSt) or less at 25 °C (77 °F), or do not contain suspended solids or do not have a tendency to form a surface film while under test. Other flash point classifications have been established by these departments for liquids using this test method. 1.2 This test method can be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and cannot be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test method can be used as elements of fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use. 1.3 Related standards are Test Methods D93, D1310, D3828, D3278, and D3941. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.5 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements see 8.2, 8.3, 9.5, 12.5, and refer to Material Safety Data Sheets. |
| 국제분류(ICS)코드 |
75.080 : 석유제품 일반
87.040 : 페인트 및 니스 |
| 페이지수 | 12 |
| Edition | 16a |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D56-22 | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2022-07-01 | 표준 |
| 2 | ASTM D56-22 REDLINE | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2022-07-01 | 표준 |
| 3 | ASTM D56-21a | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2021-12-01 | 구판 |
| 4 | ASTM D56-21a REDLINE | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2021-12-01 | 구판 |
| 5 | ASTM D56-21 | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2021-04-01 | 구판 |
| 6 | ASTM D56-21 REDLINE | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2021-04-01 | 구판 |
| 7 | ASTM D56-16a REDLINE | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2016-10-01 | 구판 |
| 8 | ASTM D56-16a | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2016-10-01 | 구판 |
| 9 | ASTM D56-16 | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2016-06-01 | 구판 |
| 10 | ASTM D56-05(2010) | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2010-10-01 | 구판 |
| 11 | ASTM D56-05 | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2005-05-01 | 구판 |
| 12 | ASTM D56-02a | Standard Test Method for Flash Point by Tag Closed Cup Tester | 2002-12-10 | 구판 |
| 13 | ASTM D56-02 | Standard Test Method for Flash Point by Tag Closed Tester | 2002-06-10 | 구판 |
| 14 | ASTM D56-00 | Standard Test Method for Flash Point by Tag Closed Tester | 2000-08-10 | 구판 |
| 15 | ASTM D56-01 | Standard Test Method for Flash Point by Tag Closed Tester | 2000-08-10 | 구판 |
| 16 | ASTM D56-87 | Standard Test Method for Flash Point by Tag Closed Tester | 구판 | |
| 17 | ASTM D56-93 | Standard Test Method for Flash Point by Tag Closed Tester | 구판 | |
| 18 | ASTM D56-70 | Standard Method Of Test For Flash Point By Tag Closed Tester | 구판 |
관련상품이 존재하지 않습니다.
ASTM D4052-18a - Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter 상세보기
ASTM D4294-16e1 - Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry 상세보기
ASTM D5972-16 - Standard Test Method for Freezing Point of Aviation Fuels (Automatic Phase Transition Method) 상세보기
ASTM D1796-11(2016) - Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) 상세보기
ASTM D1298-12b(2017) - Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
