관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Magnetic Particle Testing
| 분야 | 03.03 : 비 파괴검사 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. Guide E709 can be used in conjunction with this practice as a tutorial. Note 1: This Practice replaces MIL-STD-1949. 1.2 The magnetic particle testing method is used to detect cracks, laps, seams, inclusions, and other discontinuities on or near the surface of ferromagnetic materials. Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service parts. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. See Appendix X1 for additional information. 1.3 All areas of this Practice may be open to agreement between the Cognizant Engineering Organization and the supplier, or specific direction from the Cognizant Engineering Organization. 1.4 This standard is a combined standard, an ASTM standard in which rationalized SI units and inch-pound units are included in the same standard, with each system of units to be regarded separately as standard. 1.4.1 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 77.040.20 : 금속의 비파괴 시험 |
| 페이지수 | 22 |
| Edition | 16e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1444/E1444M-22a | Standard Practice for Magnetic Particle Testing for Aerospace | 2022-07-01 | 표준 |
| 2 | ASTM E1444/E1444M-22a REDLINE | Standard Practice for Magnetic Particle Testing for Aerospace | 2022-07-01 | 표준 |
| 3 | ASTM E1444/E1444M-22 | Standard Practice for Magnetic Particle Testing for Aerospace | 2022-06-01 | 구판 |
| 4 | ASTM E1444/E1444M-21 | Standard Practice for Magnetic Particle Testing for Aerospace | 2021-09-01 | 구판 |
| 5 | ASTM E1444/E1444M-21 REDLINE | Standard Practice for Magnetic Particle Testing for Aerospace | 2021-09-01 | 구판 |
| 6 | ASTM E1444/E1444M-20 | Standard Practice for Magnetic Particle Testing for Aerospace | 2020-12-01 | 구판 |
| 7 | ASTM E1444/E1444M-16e1 | Standard Practice for Magnetic Particle Testing | 2016-06-01 | 구판 |
| 8 | ASTM E1444/E1444M-16 | Standard Practice for Magnetic Particle Testing | 2016-06-01 | 구판 |
| 9 | ASTM E1444/E1444M-12 | Standard Practice for Magnetic Particle Testing | 2012-10-15 | 구판 |
| 10 | ASTM E1444/E1444M-11 | Standard Practice for Magnetic Particle Testing | 2011-08-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E709-15 - Standard Guide for Magnetic Particle Testing 상세보기
ASTM D4541-17 - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers 상세보기
ASTM E165/E165M-18 - Standard Practice for Liquid Penetrant Testing for General Industry 상세보기
DIN EN 1090-1:2012-02 - Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components (includes Amendment A1:2011) 상세보기
DIN EN 1090-2:2018-09 - Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
