관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
| 분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
|---|---|
| 적용범위 | 1.1 This test method determines the two-dimensional flexural properties of sandwich composite plates subjected to a distributed load. The test fixture uses a relatively large square panel sample which is simply supported all around and has the distributed load provided by a water-filled bladder. This type of loading differs from the procedure of Test Method C393, where concentrated loads induce one-dimensional, simple bending in beam specimens. 1.2 This test method is applicable to composite structures of the sandwich type which involve a relatively thick layer of core material bonded on both faces with an adhesive to thin-face sheets composed of a denser, higher-modulus material, typically, a polymer matrix reinforced with high-modulus fibers. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 12 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6416/D6416M-16(2024) | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2024-05-01 | 표준 |
| 2 | ASTM D6416/D6416M-16 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2016-04-01 | 구판 |
| 3 | ASTM D6416/D6416M-16e1 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2016-04-01 | 구판 |
| 4 | ASTM D6416/D6416M-16 REDLINE | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2016-04-01 | 구판 |
| 5 | ASTM D6416/D6416M-01(2012) | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2012-08-01 | 구판 |
| 6 | ASTM D6416/D6416M-01(2007) | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2007-01-01 | 구판 |
| 7 | ASTM D6416/D6416M-01e1 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2001-03-10 | 구판 |
| 8 | ASTM D6416/D6416M-99 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2001-03-10 | 구판 |
| 9 | ASTM D6416/D6416M-01 | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load | 2001-03-10 | 구판 |
관련상품이 존재하지 않습니다.
BS EN 50583-1:2016 - Photovoltaics in buildings. BIPV modules. 상세보기
BS EN 50085-1:2005+A1:2013 - Cable trunking systems and cable ducting systems for electrical installations. General requirements. 상세보기
ASTM C393/C393M-16 - Standard Test Method for Core Shear Properties of Sandwich Constructions by Beam Flexure 상세보기
ASTM C394/C394M-16 - Standard Test Method for Shear Fatigue of Sandwich Core Materials 상세보기
GB/T 17748-2016 - Aluminium-plastic composite panel for curtain wall 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
