K
관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
---|---|
적용범위 | 1.1 This test method covers the determination of the resistance to fracture of metallic materials under Mode I loading at static rates using either of the following notched and precracked specimens: the middle-cracked tension M(T) specimen or the compact tension C(T) specimen. A KR curve is a continuous record of toughness development (resistance to crack extension) in terms of KR plotted against crack extension in the specimen as a crack is driven under an increasing stress intensity factor, K. (1)2 1.2 Materials that can be tested for KR curve development are not limited by strength, thickness, or toughness, so long as specimens are of sufficient size to remain predominantly elastic to the effective crack extension value of interest. 1.3 Specimens of standard proportions are required, but size is variable, to be adjusted for yield strength and toughness of the materials. 1.4 Only two of the many possible specimen types that could be used to develop KR curves are covered in this method. 1.5 The test is applicable to conditions where a material exhibits slow, stable crack extension under increasing crack driving force, which may exist in relatively tough materials under plane stress crack tip conditions. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
페이지수 | 16 |
Edition | 15a |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM E561-23 | Standard Test Method for |
2023-05-01 | 표준 |
2 | ASTM E561-23 REDLINE | Standard Test Method for |
2023-05-01 | 표준 |
3 | ASTM E561-22 | Standard Test Method for |
2022-05-01 | 구판 |
4 | ASTM E561-22 REDLINE | Standard Test Method for |
2022-05-01 | 구판 |
5 | ASTM E561-21 | Standard Test Method for |
2021-12-01 | 구판 |
6 | ASTM E561-21 REDLINE | Standard Test Method for |
2021-12-01 | 구판 |
7 | ASTM E561-20 REDLINE | Standard Test Method for |
2020-06-15 | 구판 |
8 | ASTM E561-20 | Standard Test Method for |
2020-06-15 | 구판 |
9 | ASTM E561-19e1 | Standard Test Method for |
2019-07-15 | 구판 |
10 | ASTM E561-19 | Standard Test Method for |
2019-07-15 | 구판 |
11 | ASTM E561-19 REDLINE | Standard Test Method for |
2019-07-15 | 구판 |
12 | ASTM E561-15a | Standard Test Method for |
2015-12-01 | 구판 |
13 | ASTM E561-15a REDLINE | Standard Test Method for |
2015-12-01 | 구판 |
14 | ASTM E561-15 | Standard Test Method for |
2015-10-15 | 구판 |
15 | ASTM E561-10e2 | Standard Test Method for |
2010-11-01 | 구판 |
16 | ASTM E561-10e1 | Standard Test Method for K-R Curve Determination | 2010-11-01 | 구판 |
17 | ASTM E561-10 | Standard Test Method for |
2010-11-01 | 구판 |
18 | ASTM E561-08e1 | Standard Test Method for |
2008-11-01 | 구판 |
19 | ASTM E561-08 | Standard Test Method for |
2008-11-01 | 구판 |
20 | ASTM E561-05e1 | Standard Test Method for |
2005-06-01 | 구판 |
21 | ASTM E561-05 | Standard Test Method for |
2005-06-01 | 구판 |
22 | ASTM E561-98 | Standard Practice for R-Curve Determination | 1998-12-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기