관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Ball Punch Deformation of Metallic Sheet Material
| 분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
|---|---|
| 적용범위 | 1.1 This test method covers the procedure for conducting the ball punch deformation test for metallic sheet materials intended for forming applications. The test applies to specimens with thicknesses between 0.008 and 0.080 in. (0.2 and 2.0 mm). Note 1: The ball punch deformation test is intended to replace the Olsen cup test by standardizing many of the test parameters that previously have been left to the discretion of the testing laboratory. Note 2: The modified Erichsen test has been standardized in Europe. The main differences between the ball punch deformation test and the Erichsen test are the diameters of the penetrator and the dies. Erichsen cup heights are given in SI units. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
| 페이지수 | 4 |
| Edition | 15 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E643-24 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2024-05-15 | 표준 |
| 2 | ASTM E643-24 REDLINE | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2024-05-15 | 표준 |
| 3 | ASTM E643-15 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2015-05-01 | 구판 |
| 4 | ASTM E643-15 REDLINE | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2015-05-01 | 구판 |
| 5 | ASTM E643-09 | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2000-01-01 | 구판 |
| 6 | ASTM E643-84(1995) | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material | 2000-01-01 | 구판 |
| 7 | ASTM E643-84(2000) | Standard Test Method for Ball Punch Deformation of Metallic Sheet Material (Withdrawn 2009) | 2000-01-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
