관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
| 분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
|---|---|
| 적용범위 | 1.1 This test method determines the flexural stiffness and strength properties of polymer matrix composites. 1.1.1 Procedure A—A three-point loading system utilizing center loading on a simply supported beam. 1.1.2 Procedure B—A four-point loading system utilizing two load points equally spaced from their adjacent support points, with a distance between load points of one-half of the support span. Note 1: Unlike Test Method D6272, which allows loading at both one-third and one-half of the support span, in order to standardize geometry and simplify calculations this standard permits loading at only one-half the support span. 1.2 For comparison purposes, tests may be conducted according to either test procedure, provided that the same procedure is used for all tests, since the two procedures generally give slightly different property values. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 10 |
| Edition | 15 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D7264/D7264M-21 | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2021-01-01 | 표준 |
| 2 | ASTM D7264/D7264M-21 REDLINE | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2021-01-01 | 표준 |
| 3 | ASTM D7264/D7264M-15 REDLINE | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2015-04-01 | 구판 |
| 4 | ASTM D7264/D7264M-15 | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2015-04-01 | 구판 |
| 5 | ASTM D7264/D7264M-07 | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2007-04-01 | 구판 |
| 6 | ASTM D7264/D7264M-06 | Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials | 2006-11-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D5961/D5961M-17 - Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates 상세보기
ASTM D6641/D6641M-16e1 - Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture 상세보기
ASTM D2344/D2344M-16 - Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates 상세보기
ASTM D7136/D7136M-15 - Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event 상세보기
ASTM D6484/D6484M-14 - Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
