관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Seamless Stainless Steel Mechanical Tubing
| 분야 | 01.01 : 철강-배관, 튜브, 관이음쇠 |
|---|---|
| 적용범위 | 1.1 This specification covers seamless stainless tubing for use in mechanical applications where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1, Table 2, and Table 3. (A) For small diameter or thin wall tubing or both, where many drawing passes are required, a maximum of 0.040 % carbon is necessary in grades MT-304L and MT-316L. Small outside diameter tubes are defined as those under a 0.500 in. [12.7 mm] outside diameter and light-wall tubes as those under a 0.049 in. [1.2 mm] average wall thickness (0.044 in. [1.1 mm] min wall thickness). (B) Iron shall be determined arithmetically by difference of 100 minus the sum of the other specified elements. (C) The range of (Al + Ti) shall be within 0.85–1.20 %. (A) MT446-2 is a lower carbon version of MT446-1, that has a lower tensile strength but improved ductility and toughness. (B) Carbon plus nitrogen = 0.025 max %. (A) Maximum, unless a range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement and analysis for the element need not be determined or reported. (B) % Cr + 3.3 X % Mo + 16X % N ≥ 40. 1.2 This specification covers seamless cold-finished mechanical tubing and seamless hot-finished mechanical tubing in sizes up to 123/4 in. [325 mm] in outside nominal diameter (for round tubing) with wall thicknesses as required. 1.3 Tubes shall be furnished in one of the following shapes, as specified by the purchaser: round, square, rectangular, or special. 1.4 Optional supplementary requirements are provided and when desired, shall be stated in the order. 1.5 The values stated in inch-pound units are to be regarded as the standard. Within the text, the SI units are shown in square brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. |
| 국제분류(ICS)코드 | |
| 페이지수 | 12 |
| Edition | 15 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A511/A511M-21a | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2021-11-01 | 표준 |
| 2 | ASTM A511/A511M-21a REDLINE | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2021-11-01 | 표준 |
| 3 | ASTM A511/A511M-21 | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2021-09-01 | 구판 |
| 4 | ASTM A511/A511M-20 | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2020-11-01 | 표준 |
| 5 | ASTM A511/A511M-20 REDLINE | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2020-11-01 | 표준 |
| 6 | ASTM A511/A511M-16 REDLINE | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2016-05-01 | 구판 |
| 7 | ASTM A511/A511M-16 | Standard Specification for Seamless Stainless Steel Mechanical Tubing and Hollow Bar | 2016-05-01 | 구판 |
| 8 | ASTM A511/A511M-15a | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2015-05-01 | 구판 |
| 9 | ASTM A511/A511M-15 | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2015-01-01 | 구판 |
| 10 | ASTM A511/A511M-12 | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2012-03-01 | 구판 |
| 11 | ASTM A511/A511M-11 | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2011-10-01 | 구판 |
| 12 | ASTM A511/A511M-08 | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2008-01-01 | 구판 |
| 13 | ASTM A511/A511M-07 | Standard Specification for Seamless Stainless Steel Mechanical Tubing | 2007-11-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
