관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service
| 분야 | 01.01 : 철강-배관, 튜브, 관이음쇠 |
|---|---|
| 적용범위 | 1.1 This specification covers grades of stainless steel tubing in sizes under 1/2 down to 0.050 in. (12.7 to 1.27 mm) in outside diameter and wall thicknesses less than 0.065 in. down to 0.005 in. (1.65 to 0.13 mm) for general corrosion-resisting and low- or high-temperature service, as designated in Table 1. Note 1: The grades of austenitic stainless steel tubing furnished in accordance with this specification have been found suitable for low-temperature service down to −325°F (−200°C) in which Charpy notched-bar impact values of 15 ft·lbf (20 J), minimum, are required and these grades need not be impact tested. (A) New designation established in accordance with Practice E527 and SAE J 1086, Practice for Numbering Metals and Alloys (UNS). (B) For seamless TP316L tubes, the silicon maximum shall be 1.00 %. (C) For welded TP 316 tubes, the nickel range shall be 10.0–14.0 %. (D) Grade TP 321 shall have a titanium content of not less than five times the carbon content and not more than 0.60 %. (E) Grades TP 347 and TP 348 shall have a columbium plus tantalum content of not less than ten times the carbon content and not more than 1.0 %. 1.2 Optional supplementary requirements are provided and, when desired, shall be so stated in the order. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. |
| 국제분류(ICS)코드 |
23.040.40 : 금속 조립품
23.040.10 : 주철 및 강 파이프 |
| 페이지수 | 4 |
| Edition | 04(2014) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A632-19 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2019-09-01 | 표준 |
| 2 | ASTM A632-19 REDLINE | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2019-09-01 | 표준 |
| 3 | ASTM A632-04(2014) | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2014-10-01 | 구판 |
| 4 | ASTM A632-04(2009) | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2004-03-01 | 구판 |
| 5 | ASTM A632-04 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2004-03-01 | 구판 |
| 6 | ASTM A632-02a | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2002-09-10 | 구판 |
| 7 | ASTM A632-02 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2002-03-10 | 구판 |
| 8 | ASTM A632-01 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2001-05-10 | 구판 |
| 9 | ASTM A632-98 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service | 2001-05-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
