관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
---|---|
적용범위 | 1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Test Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content (by weight or volume), and the cured ply thickness, based on the measured thickness of the laminate. Test Method II is not applicable to the measurement of void volume. 1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case. 1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal matrices. The suggested applications are discussed in Section 4, as well as at the start of each procedure. 1.1.3 Test Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium. A procedure for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace. 1.1.4 Test Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an acceptable tolerance. The presence of voids is not measured. Eq 9 and 10 assume zero void content to perform the calculation. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional information. |
국제분류(ICS)코드 | |
페이지수 | 10 |
Edition | 11 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D3171-22 | Standard Test Methods for Constituent Content of Composite Materials | 2022-03-01 | 표준 |
2 | ASTM D3171-22 REDLINE | Standard Test Methods for Constituent Content of Composite Materials | 2022-03-01 | 표준 |
3 | ASTM D3171-15 | Standard Test Methods for Constituent Content of Composite Materials | 2015-04-01 | 구판 |
4 | ASTM D3171-15 REDLINE | Standard Test Methods for Constituent Content of Composite Materials | 2015-04-01 | 구판 |
5 | ASTM D3171-11 | Standard Test Methods for Constituent Content of Composite Materials | 2011-10-01 | 구판 |
6 | ASTM D3171-09 | Standard Test Methods for Constituent Content of Composite Materials | 2009-04-01 | 구판 |
7 | ASTM D3171-06 | Standard Test Methods for Constituent Content of Composite Materials | 2006-04-01 | 구판 |
8 | ASTM D3171-99(2004) | Standard Test Methods for Constituent Content of Composite Materials | 2004-11-01 | 구판 |
9 | ASTM D3171-99 | Standard Test Methods for Constituent Content of Composite Materials | 1999-10-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기