관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 1These test methods cover the measurement of apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. Different procedures are given for application to the various forms of these materials that are commonly encountered, from fine powders and granules to large flakes and cut fibers. 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1—Test Method A is equivalent to ISO Method R 60 as described in the appendix. Test Method C is identical with ISO Method R 61. 5.1 Test Method A (see Note 1) covers the measurement of the apparent density of the fine granules and powders that can be poured readily through a small funnel. 8.1 Test Method B covers the measurement of the apparent density of coarse, granular materials, including dice and pellets, that either cannot be poured or that pour with difficulty through the funnel described in Test Method A. 11.1 Test Method C (see Note 1) covers the measurement of the apparent density of materials supplied in the form of coarse flakes, chips, cut fibers, or strands. Such materials cannot be poured through the funnels described in Test Methods A and B. Also, since they ordinarily are very bulky when loosely poured and since they usually are compressible to a lesser bulk, even by hand, a measure of their density under a small load is appropriate and useful. |
| 국제분류(ICS)코드 | |
| 페이지수 | 6 |
| Edition | 96(2010)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1895-24 | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2024-08-01 | 표준 |
| 2 | ASTM D1895-24 REDLINE | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2024-08-01 | 표준 |
| 3 | ASTM D1895-17 | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2017-09-01 | 구판 |
| 4 | ASTM D1895-17 REDLINE | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2017-09-01 | 구판 |
| 5 | ASTM D1895-96(2010)e1 | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2010-01-01 | 구판 |
| 6 | ASTM D1895-96(2010) | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2010-01-01 | 구판 |
| 7 | ASTM D1895-96(2003) | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 2003-04-10 | 구판 |
| 8 | ASTM D1895-96 | Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials | 1996-04-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
