관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Castings, Austenitic, for Pressure-Containing Parts
| 분야 | 01.02 : 주철-철합금 |
|---|---|
| 적용범위 | 1.1 This specification covers austenitic steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 0). Note 0Carbon steel castings for pressure-containing parts are covered by Specification A 216/A 216M, low-alloy steel castings by Specification A 217/A 217M, and duplex stainless steel castings by Specification A 995/A 995M. 1.2 A number of grades of austenitic steel castings are included in this specification. Since these grades possess varying degrees of suitability for service at high temperatures or in corrosive environments, it is the responsibility of the purchaser to determine which grade shall be furnished. Selection will depend on design and service conditions, mechanical properties, and high-temperature or corrosion-resistant characteristics, or both. 1.2.1 Because of thermal instability, Grades CE20N, CF3A, CF3MA, and CF8A are not recommended for service at temperatures above 800F [425C]. 1.2.2 Because of embrittlement phases, Grade CD4MCu is not recommended for service at temperatures above 600F [316C]. 1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The Supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.4 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. |
| 국제분류(ICS)코드 | |
| 페이지수 | 5 |
| Edition | 06 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A351/A351M-24 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2024-05-01 | 표준 |
| 2 | ASTM A351/A351M-24 REDLINE | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2024-05-01 | 표준 |
| 3 | ASTM A351/A351M-18e1 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
| 4 | ASTM A351/A351M-18 REDLINE | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
| 5 | ASTM A351/A351M-18 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2018-05-01 | 구판 |
| 6 | ASTM A351/A351M-16 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2016-05-01 | 구판 |
| 7 | ASTM A351/A351M-15 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2015-09-01 | 구판 |
| 8 | ASTM A351/A351M-14 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2014-05-01 | 구판 |
| 9 | ASTM A351/A351M-13a | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2013-05-15 | 구판 |
| 10 | ASTM A351/A351M-13 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2013-05-01 | 구판 |
| 11 | ASTM A351/A351M-12b | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-11-01 | 구판 |
| 12 | ASTM A351/A351M-12a | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-09-01 | 구판 |
| 13 | ASTM A351/A351M-12 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2012-03-01 | 구판 |
| 14 | ASTM A351/A351M-10 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2010-04-01 | 구판 |
| 15 | ASTM A351/A351M-06 | Standard Specification for Castings, Austenitic, for Pressure-Containing Parts | 2006-03-01 | 구판 |
| 16 | ASTM A351/A351M-05 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2005-05-01 | 구판 |
| 17 | ASTM A351/A351M-03 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2003-05-10 | 구판 |
| 18 | ASTM A351/A351M-00 | Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts | 2000-09-10 | 구판 |
| 19 | ASTM A351/A351M-94 | Standard Specification for Castings, Austenitic, Austenitic- Ferritic (Duplex), for Pressure-Containing Parts | 구판 |
관련상품이 존재하지 않습니다.
ASTM A36/A36M-08 - Standard Specification for Carbon Structural Steel 상세보기
ASTM A285/A285M-03(2007) - Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength 상세보기
ASTM A53/A53M-07 - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless 상세보기
ASTM A283/A283M-03(2007) - Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates 상세보기
ASTM A516/A516M-06 - Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
