관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique
| 분야 | 14.05 : 통계 방법; 화학 물질의 잠재적 위험성; 열측정; 약품 제조 |
|---|---|
| 적용범위 | 1.1 This test method describes a steady state technique for the determination of the thermal conductivity, [lambda], of homogeneous-opaque solids (see Notes 1 and 2). This test method is for materials with effective conductivities in the approximate range 0.2 ∧ [lambda] ∧ 200 W/ [dot]K over the approximate temperature range between 90 and 1300 K. It can be used outside these ranges with decreased accuracy. Note 1-For purposes of this technique, a system is homogeneous if the apparent thermal conductivity of the specimen, [lambda] , does not vary with changes of thickness or cross-sectional area by more than +5%. For composites or heterogeneous systems consisting of slabs or plates bonded together, the specimen should be more than 20 units wide and 20 units thick, respectively, where a unit is the thickness of the thickest slab or plate, so that diameter or length changes of one-half unit will affect the apparent [lambda] by less than +5%. For systems that are non-opaque or partially transparent in the infrared, the combined error due to inhomogeneity and photon transmission should be less than +5%. Measurements on highly transparent solids must be accompanied with infrared absorption coefficient information or the results must be reported as apparent [lambda] . Note 2-This test method may also be used to evaluate the thermal conductance/resistance of materials in contact.1.2 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 8 |
| Edition | 99 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1225-20 | Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique | 2020-09-01 | 표준 |
| 2 | ASTM E1225-20 REDLINE | Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique | 2020-09-01 | 표준 |
| 3 | ASTM E1225-13 | Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique | 2013-10-01 | 구판 |
| 4 | ASTM E1225-13 REDLINE | Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique | 2013-10-01 | 구판 |
| 5 | ASTM E1225-09 | Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique | 2009-03-15 | 구판 |
| 6 | ASTM E1225-04 | Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique | 2004-05-01 | 구판 |
| 7 | ASTM E1225-99 | Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique | 1999-03-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
