관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
초안
절판(중지)
ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal threads to mate with hot-dip galvanized external threads with maximum size of tolerance position h before galvanizing
| 언어 | 제공형태 | 판매가격 | 선택 |
|---|---|---|---|
|
영어 |
|
66,900원 |
|
|
영어 |
|
66,900원 |
|
| 분야 | ISO/TC 1 : Screw threads |
|---|---|
| 적용범위 | This part of ISO 965 specifies deviations and limits of sizes for pitch and crest diameters for ISO general purpose metric internal screw threads conforming to ISO 262 having basic profile according to ISO 68-1. Internal screw threads according to this part of ISO 965 are intended to mate with external screw threads with maximum size of tolerance position h before hot-dip galvanizing. The limits of sizes for the tolerance quality specified are derived from tolerances specified in ISO 965-1. The fundamental deviations for internal screw threads with a tolerance position AZ have been calculated according to the following formula: EIAZ = + (300 + 20P) Where EI is expressed in micrometers. P is expressed in millimeters. The fundamental deviations for internal screw threads with a tolerance position AX have been calculated according to the following formula: EIAX = + (220P - 20) Where EI is expressed in micrometers; P is expressed in millimeters. Products made with thread tolerances according to this part of ISO 965 may show load failure when tested in accordance with ISO 898-2 without adjustment of the other mechanical properties. Internal screw threads with thread tolerances according to this part of ISO 965 must not be mated with external screw threads having thread tolerances according to ISO 965-4 because such combinations will create severe risk of thread stripping. NOTE Internal screw threads with tolerance class 6AZ are primarily intended to mate with external screw threads centrifuged after hot-dip galvanizing. Internal screw threads with tolerance class 6AX are primarily intended to mate with hot-dip galvanized external screw threads with heavy coating not centrifuged. |
| 국제분류(ICS)코드 | 21.040.10 : 미터나사 |
| 페이지수 | 5 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 965-5:1998/Amd 1:2021 | ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing — Amendment 1 | 2021-07-06 | 표준 |
| 2 | ISO 965-5:1998 | ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing | 1998-12-20 | 표준 |
ISO/DIS 965-6 - ISO general purpose metric screw threads — Tolerances — Part 6: Limits of sizes for internal and external threads (Fine and medium tolerance qualities, first and second choices) 상세보기
ISO/DIS 965-1 - ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data 상세보기
ISO/FDIS 965-4 - ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external threads to mate with internal threads made to tolerance position H or G after galvanizing 상세보기
ISO 965-5:1998 - ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing 상세보기
ISO 965-1:2013 - ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
