관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Paints and varnishes — Cross-cut test
| 분야 | ISO/TC 35/SC 9 : General test methods for paints and varnishes |
|---|---|
| 적용범위 | This document specifies a test method for assessing the resistance of paint coatings and varnishes (including wood stains) to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate. The property determined by this empirical test procedure depends, among other factors, on the adhesion of the coating to either the preceding coat or the substrate. This procedure is not, however, a means of measuring adhesion. NOTE 1 Where a measurement of adhesion is required, see the method described in ISO 4624. NOTE 2 Although the test is primarily intended for use in the laboratory, the test is also suitable for field testing. The method described can be used either as a pass/fail test or, where circumstances are appropriate, as a six-step classification test. When applied to a multi-coat system, assessment of the resistance to separation of individual layers of the coating from each other can be made. The test can be carried out on finished objects and/or on specially prepared test specimens. Although the method is applicable to paint on hard (e.g. metal) and soft (e.g. wood and plaster) substrates, these different substrates need a different test procedure (see Clause 8). The method is not suitable for coatings of total thickness greater than 250 µm or for textured coatings. NOTE 3 The method, when applied to coatings designed to give a rough patterned surface, will give results which will show too much variation (see also ISO 16276-2). |
| 국제분류(ICS)코드 | 87.040 : 페인트 및 니스 |
| 페이지수 | 14 |
| Edition | 5 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 2409:2020 | Paints and varnishes — Cross-cut test | 2020-08-31 | 표준 |
| 2 | ISO 2409:2013 | Paints and varnishes — Cross-cut test | 2013-02-12 | 구판 |
| 3 | ISO 2409:2007 | Paints and varnishes — Cross-cut test | 2007-05-11 | 구판 |
| 4 | ISO 2409:1992 | Paints and varnishes -- Cross-cut test | 1992-08-20 | 구판 |
| 5 | ISO 2409:1972 | Paints and varnishes -- Cross-cut test | 1972-08-01 | 구판 |
관련상품이 존재하지 않습니다.
ISO 8503-1:2012 - Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces 상세보기
ISO 8503-2:2012 - Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure 상세보기
ISO 8503-5:2017 - Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determination of the surface profile 상세보기
ISO 4624:2016 - Paints and varnishes — Pull-off test for adhesion 상세보기
ISO 2808:2019 - Paints and varnishes — Determination of film thickness 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
