관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures
| 분야 | ISO/TC 45/SC 2 : Testing and analysis |
|---|---|
| 적용범위 | This document specifies two methods for the determination of the compression set characteristics of vulcanized and thermoplastic rubbers at low temperatures. Method 1 derives from the methodology used in ISO 815-1. Method 2 uses a specified testing device, allowing to measure and record the test piece thickness during recovery. Due to the load applied during recovery in method 2, no correlation can be established between the results given by both methods. NOTE When rubber is held under compression, physical or chemical changes that prevent the rubber returning to its original dimensions after release of the deforming force can occur. The result is a set, where the magnitude of which depends on the time and temperature of compression as well as on the time, temperature, and conditions of recovery. At low temperatures, changes resulting from the effects of glass hardening or crystallization become predominant and, since these effects are reversed by raising the temperature, therefore, the measurements are always taken at the test temperature. |
| 국제분류(ICS)코드 | 83.060 : 고무 |
| 페이지수 | 20 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 815-2:2019 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures | 2019-11-26 | 표준 |
| 2 | ISO 815-2:2014 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures | 2014-11-05 | 구판 |
| 3 | ISO 815-2:2008 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures | 2008-01-28 | 구판 |
ISO 815-1:2019 - Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures 상세보기
ISO 815-1:2019 - Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures 상세보기
ISO 23529:2016 - Rubber — General procedures for preparing and conditioning test pieces for physical test methods 상세보기
KS M ISO 815-2 - 가황 또는 열가소성 고무－제2부：저온에서의 영구압축률 측정방법 상세보기
ISO 11357-2:2020 - Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height 상세보기
ISO 6721-11:2019 - Plastics — Determination of dynamic mechanical properties — Part 11: Glass transition temperature 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
