관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Test code for machine tools — Part 3: Determination of thermal effects
| 분야 | ISO/TC 39/SC 2 : Test conditions for metal cutting machine tools |
|---|---|
| 적용범위 | This document defines four tests: — an environmental temperature variation error (ETVE) test; — a test for thermal distortion caused by rotating spindles; — a test for thermal distortion caused by moving linear axes; — a test for thermal distortion caused by rotary motion of components. The tests for thermal distortion caused by moving linear axes (see Clause 7) are applicable to numerically controlled (NC) machines only and are designed to quantify the effects of thermal expansion and contraction as well as the angular deformation of structures. For practical reasons, the test methods described in Clause 7 apply to machines with linear axes up to 2 000 mm in length. If they are used for machines with axes longer than 2 000 mm, a representative length of 2 000 mm in the normal range of each axis is chosen for the tests. The tests correspond to the drift test procedure as described in ISO/TR 16015:2003, A.4.2, applied for machine tools with special consideration of thermal distortion of moving linear components and thermal distortion of moving rotary components. On machine tools equipped with compensation for thermal effects these tests demonstrate any uncertainty in nominal thermal expansion due to uncertainty of coefficient of thermal expansion and any uncertainty of length due to temperature measurement. |
| 국제분류(ICS)코드 | 25.080.01 : 공작기계 일반 |
| 페이지수 | 50 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 230-3:2020 | Test code for machine tools — Part 3: Determination of thermal effects | 2020-11-16 | 표준 |
| 2 | ISO 230-3:2007 | Test code for machine tools — Part 3: Determination of thermal effects | 2007-08-06 | 구판 |
| 3 | ISO 230-3:2001 | Test code for machine tools — Part 3: Determination of thermal effects | 2001-03-08 | 구판 |
ISO/DIS 230-5 - Test code for machine tools — Part 5: Determination of the noise emission 상세보기
ISO 230-5:2000 - Test code for machine tools -- Part 5: Determination of the noise emission 상세보기
ISO 230-6:2002 - Test code for machine tools — Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests) 상세보기
ISO/TR 230-9:2005 - Test code for machine tools — Part 9: Estimation of measurement uncertainty for machine tool tests according to series ISO 230, basic equations 상세보기
ISO/TR 230-8:2010 - Test code for machine tools — Part 8: Vibrations 상세보기
ISO 230-7:2015 - Test code for machine tools — Part 7: Geometric accuracy of axes of rotation 상세보기
ISO 230-1:2012 - Test code for machine tools — Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions 상세보기
ISO 230-2:2014/Amd 1:2016 - Test code for machine tools — Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes — Amendment 1 상세보기
ISO 8636-2:2007 - Machine tools — Test conditions for bridge-type milling machines — Testing of the accuracy — Part 2: Travelling bridge (gantry-type) machines 상세보기
ISO 10791-10:2007 - Test conditions for machining centres — Part 10: Evaluation of thermal distortions 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
