관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Determination of creep behaviour — Part 1: Tensile creep
| 분야 | ISO/TC 61/SC 2 : Mechanical behavior |
|---|---|
| 적용범위 | ISO 899-1 specifies a method for determining the tensile creep of plastics in the form of standard test specimens under specified conditions such as those of pretreatment, temperature and humidity. The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials in the form of dumb-bell-shaped test specimens moulded directly or machined from sheets or moulded articles. The method is intended to provide data for engineering-design and research and development purposes. Data for engineering-design purposes requires the use of extensometers to measure the gauge length of the specimen. Data for research or quality-control purposes may use the change in distance between the grips (nominal extension). Tensile creep can vary significantly with differences in specimen preparation and dimensions and in the test environment. The thermal history of the test specimen can also have profound effects on its creep behaviour (see Annex A). Consequently, when precise comparative results are required, these factors are intended to be carefully controlled. If tensile-creep properties are used for engineering-design purposes, the plastics materials are intended to be tested over a broad range of stresses, times and environmental conditions. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 14 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep | 2017-10-02 | 표준 |
| 2 | ISO 899-1:2003/Amd 1:2015 | Plastics — Determination of creep behaviour — Part 1: Tensile creep — Amendment 1 | 2015-03-10 | 구판 |
| 3 | ISO 899-1:2003 | Plastics — Determination of creep behaviour — Part 1: Tensile creep | 2003-06-03 | 구판 |
| 4 | ISO 899-1:1993 | Plastics -- Determination of creep behaviour -- Part 1: Tensile creep | 1993-12-23 | 구판 |
ISO 899-2:2024 - Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading 상세보기
ISO 899-2:2003 - Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading 상세보기
ISO 472:2013/Amd 1:2018 - Plastics — Vocabulary — Amendment 1: Additional items 상세보기
ISO 472:2013 - Plastics — Vocabulary 상세보기
ISO 18872:2007 - Plastics — Determination of tensile properties at high strain rates 상세보기
ISO 7765-2:1994 - Plastics film and sheeting — Determination of impact resistance by the free-falling dart method — Part 2: Instrumented puncture test 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
