관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Gears — Surface temper etch inspection after grinding, chemical method
| 분야 | ISO/TC 60/SC 2 : Gear capacity calculation |
|---|---|
| 적용범위 | ISO 14104:2017 specifies procedures and requirements for the detection and classification of localized overheating on ground surfaces by chemical etch methods. The process described in this document is typically used on ground surfaces; however, it is also useful for the detection of surface anomalies that result from post-heat treatment machining such as hard turning, milling and edge breaking (deburring) processes. Surface metallurgical anomalies caused by carburization or decarburization are also readily detectable with this process. Some methods which have been used in the past are no longer recommended. Specifications are intended to be changed to use the methods in this document. These etching methods are more sensitive to changes in surface hardness than most hardness testing methods. ISO 14104:2017 applies to steel parts such as gears, shafts, splines and bearings. It is not applicable to nitrided parts and stainless steels. NOTE This process, although at times called "nital etch", is not intended to be confused with other processes also known as "nital etch". The surface temper etch procedure is performed after grinding and before additional finishing operations such as superfinishing, shot peening and honing. |
| 국제분류(ICS)코드 | 21.200 : 기어류 |
| 페이지수 | 17 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 14104:2017 | Gears — Surface temper etch inspection after grinding, chemical method | 2017-04-04 | 표준 |
| 2 | ISO 14104:2014 | Gears — Surface temper etch inspection after grinding, chemical method | 2014-05-28 | 구판 |
| 3 | ISO 14104:1995 | Gears — Surface temper etch inspection after grinding | 1995-12-14 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E2375-16 REDLINE - Standard Practice for Ultrasonic Testing of Wrought Products 상세보기
ASTM E381-17 REDLINE - Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings 상세보기
ASTM E536-16 REDLINE - Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys 상세보기
ASTM F2215-15 REDLINE - Standard Specification for Balls, Bearings, Ferrous and Nonferrous for Use in Bearings, Valves, and Bearing Applications 상세보기
ASTM A1089/A1089M-14(2020) - Standard Specification for Highly Loaded Anti-Friction Bearing Steel 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
