관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Safety of machinery — Two-hand control devices — Principles for design and selection
| 분야 | ISO/TC 199 : Safety of machinery |
|---|---|
| 적용범위 | This document specifies the safety requirements of a two-hand control device (THCD) and the dependency of the output signal from the actuation by hand of the control actuating devices. This document describes the main characteristics of THCDs for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hold-to-run devices or as special control devices. This document does not specify with which machines THCDs shall be used. It also does not specify which types of two-hand-control device shall be used for a specific application. Moreover, while guidance is given, it does not specify the required distance between the THCD and the danger zone (see 8.8). This document provides requirements for design and guidance on the selection (based on a risk assessment) of THCDs including the prevention of defeat, the avoidance of faults and verification of compliance. NOTE 1 A THCD only offers protection for the person using it. NOTE 2 For specific machines, the suitability of a two-hand control as a suitable protective device can be defined in a type-C standard. If such a standard does not exist or is not appropriate, the risk assessment and determination of suitable protective measures is the responsibility of the manufacturer of the machine. This document applies to all THCDs, independent of the energy used, including: — THCDs which are fully assembled for installation; — THCDs which are assembled by the machine manufacturer or integrator. This document is not applicable to THCDs manufactured before the date of its publication. |
| 국제분류(ICS)코드 | 13.110 : 기계 안전성 |
| 페이지수 | 21 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 13851:2019 | Safety of machinery — Two-hand control devices — Principles for design and selection | 2019-03-19 | 표준 |
| 2 | ISO 13851:2002 | Safety of machinery — Two-hand control devices — Functional aspects and design principles | 2002-03-21 | 구판 |
관련상품이 존재하지 않습니다.
IEC 60204-1:2016 - Safety of machinery - Electrical equipment of machines - Part 1: General requirements 상세보기
ISO 13855:2010 - Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body 상세보기
ISO 14119:2013 - Safety of machinery — Interlocking devices associated with guards — Principles for design and selection 상세보기
ISO 14120:2015 - Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards 상세보기
ISO 13850:2015 - Safety of machinery — Emergency stop function — Principles for design 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
