관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions
| 분야 | ISO/TC 138/SC 2 : Plastics pipes and fittings for water supplies |
|---|---|
| 적용범위 | This document specifies the mating dimensions for thermoplastic flange adapters and corresponding loose backing flanges intended to be used in thermoplastic piping systems for the conveyance of fluids under pressure. It applies to flange adapters and loose backing flanges for use with pipes with nominal outside diameters (dn) from 16 mm to 2 500 mm and nominal pressures up to 25 bar[1] (PN 25). This document specifies the dimensions of the flange adapters intended to be used for: — butt fusion piping systems; — socket fusion piping systems; — adhesive jointed piping systems. NOTE 1 For specific connections with dimensions (e.g. dn450 or dn630) not covered in this document, or specific equipment (butterfly valves), specific solutions are available on the market. This document is applicable to loose backing flanges made from metal, thermoplastics, or a combination of metal and thermoplastics. This document also provides information on gaskets and gives general recommendations on correct assembling practices. NOTE 2 Industrial applications are not covered by this document. Products intended for industrial application are covered by ISO 15493[1], ISO 15494 or ISO 10931[2]. [1] 1 bar = 0,1 MPa = 105 N/m2. |
| 국제분류(ICS)코드 | 23.040.60 : 플랜지, 연결 및 기타 파이프 연결 |
| 페이지수 | 19 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 9624:2019/Amd 1:2021 | Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions — Amendment 1 | 2021-09-29 | 표준 |
| 2 | ISO 9624:2019 | Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions | 2019-07-12 | 표준 |
| 3 | ISO 9624:1997 | Thermoplastics pipes for fluids under pressure — Mating dimensions of flange adapters and loose backing flanges | 1997-02-13 | 구판 |
관련상품이 존재하지 않습니다.
ASTM F3565-23 - Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service 상세보기
ASTM F1412-22 - Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems 상세보기
ASTM F1055-16a(2022) - Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing 상세보기
ASTM F2136-18 - Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe 상세보기
ASTM F2807-13(2018) - Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications (Withdrawn 2024) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
