관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Tolerances for fasteners — Part 3: Washers for bolts, screws and nuts — Product grades A, C and F
| 분야 | ISO/TC 2 : Fasteners |
|---|---|
| 적용범위 | ISO 4759-3:2016 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts. This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers. It applies to non-captive and captive washers, and to standard and non-standard washers. It does not apply to dynamic disc springs. Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C. NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances). Annex A presents tolerances taken from ISO 286‑1 and ISO 286‑2. |
| 국제분류(ICS)코드 | 21.060.30 : 와셔. 잠금 장치 |
| 페이지수 | 11 |
| Edition | 4 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 4759-3:2016 | Tolerances for fasteners — Part 3: Washers for bolts, screws and nuts — Product grades A, C and F | 2016-06-01 | 표준 |
| 2 | ISO 4759-3:2000 | Tolerances for fasteners — Part 3: Plain washers for bolts, screws and nuts — Product grades A and C | 2000-05-11 | 구판 |
| 3 | ISO 4759-3:1991 | Tolerances for fasteners — Part 3: Plain washers for bolts, screws and nuts with nominal thread diameters from 1 mm up to and including 150 mm — Product grades A and C | 1991-10-17 | 구판 |
| 4 | ISO 4759-3:1977 | Tolerances for fasteners — Part 3: Washers for metric bolts, screws and nuts with thread diameters from 1 up to and including 150 mm — Product grades A and C | 1977-05-01 | 구판 |
ISO 10684:2004 - Fasteners — Hot dip galvanized coatings 상세보기
ISO 16047:2005/Amd 1:2012 - Fasteners — Torque/clamp force testing — Amendment 1 상세보기
ISO 16047:2005 - Fasteners — Torque/clamp force testing 상세보기
ISO 8992:2005 - Fasteners — General requirements for bolts, screws, studs and nuts 상세보기
ISO 225:2010 - Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
