관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Geotechnical investigation and testing — Laboratory testing of soil — Part 6: Fall cone test
| 분야 | ISO/TC 182 : Geotechnics |
|---|---|
| 적용범위 | ISO 17892-6:2017 specifies a method of undrained strength index testing of both undisturbed and remoulded specimens of fine grained soils by the fall cone method. ISO 17892-6:2017 is applicable to the laboratory estimation of undrained shear strength of a soil test specimen within the scope of geotechnical investigations. In the fall cone test, a cone is allowed to fall with its tip towards a soil specimen, and the resulting penetration of the cone into the soil is measured. The penetration values are used to estimate the undrained shear strength. The fall cone test produces a complex shear in the test specimen, and does not represent either a vertical triaxial compression or a horizontal shear test. However, this index test may be correlated to some estimate of undrained shear strength determined in the laboratory by other test methods. As the test is performed on a small laboratory specimen, the result may not agree with laboratory tests on larger specimens. In addition, the test specimen may not be fully representative of the soil in its natural state in the field; for example, the test specimen may not have fissures present in situ at a larger spacing than the specimen size. Therefore, for the above reasons, the test can be regarded as an estimation of undrained shear strength, rather than a true measurement of it. The ratio of the remoulded shear strength to the undisturbed shear strength may be used to estimate the sensitivity of a soil specimen. Time-dependent measurement of the shear strength may be used to assess the thixotropic regain of strength of a remoulded soil specimen. NOTE This document fulfils the requirements of the strength index testing of soils for geotechnical investigation and testing in accordance with EN 1997?1 and EN 1997?2. |
| 국제분류(ICS)코드 |
93.020 : 토공. 굴착. 기초건설. 갱내작업
13.080.20 : 토양의 물리적 특성 |
| 페이지수 | 11 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 17892-6:2017 | Geotechnical investigation and testing — Laboratory testing of soil — Part 6: Fall cone test | 2017-03-03 | 표준 |
| 2 | ISO/TS 17892-6:2004 | Geotechnical investigation and testing — Laboratory testing of soil — Part 6: Fall cone test | 2004-10-21 | 구판 |
ISO 17892-1:2014 - Geotechnical investigation and testing — Laboratory testing of soil — Part 1: Determination of water content 상세보기
ISO 17892-2:2014 - Geotechnical investigation and testing — Laboratory testing of soil — Part 2: Determination of bulk density 상세보기
ISO 17892-3:2015 - Geotechnical investigation and testing — Laboratory testing of soil — Part 3: Determination of particle density 상세보기
ISO 17892-4:2016 - Geotechnical investigation and testing — Laboratory testing of soil — Part 4: Determination of particle size distribution 상세보기
ISO 17892-5:2017 - Geotechnical investigation and testing — Laboratory testing of soil — Part 5: Incremental loading oedometer test 상세보기
ISO 17892-1:2014 - Geotechnical investigation and testing — Laboratory testing of soil — Part 1: Determination of water content 상세보기
ISO 17892-2:2014 - Geotechnical investigation and testing — Laboratory testing of soil — Part 2: Determination of bulk density 상세보기
ISO 17892-3:2015 - Geotechnical investigation and testing — Laboratory testing of soil — Part 3: Determination of particle density 상세보기
ISO 17892-4:2016 - Geotechnical investigation and testing — Laboratory testing of soil — Part 4: Determination of particle size distribution 상세보기
ISO 17892-5:2017 - Geotechnical investigation and testing — Laboratory testing of soil — Part 5: Incremental loading oedometer test 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
