관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners with specified hardness classes — Coarse thread and fine pitch thread
| 분야 | ISO/TC 2/SC 11 : Fasteners with metric external thread |
|---|---|
| 적용범위 | ISO 898-5:2012 specifies mechanical and physical properties of set screws and similar threaded fasteners made of carbon steel or alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Fasteners (the term used when set screws and similar threaded fasteners are considered all together) which conform to the requirements of ISO 898-5:2012 are evaluated at that ambient temperature range. Fasteners according to ISO 898-5:2012 are classified to specified hardness classes and are intended for use under compressive stress only. ISO 898-5:2012 is applicable to set screws and similar fasteners:
|
| 국제분류(ICS)코드 | 21.060.10 : 볼트. 나사. 스터드 |
| 페이지수 | 15 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners with specified hardness classes — Coarse thread and fine pitch thread | 2012-05-30 | 표준 |
| 2 | ISO 898-5:1998 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners not under tensile stresses | 1998-07-23 | 구판 |
| 3 | ISO 898-5:1980 | Mechanical properties of fasteners -- Part 5: Set screws and similar threaded fasteners not under tensile stresses | 1980-07-01 | 구판 |
ISO/DIS 898-6 - Mechanical properties of fasteners made of carbon steel and alloy steel — Part 6: Nuts with specified proof load values — Fine pitch thread 상세보기
ISO 898-4:1972 - Withdrawal of ISO 898/4-1972 상세보기
ISO 898-7:1992 - Mechanical properties of fasteners -- Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 상세보기
ISO 898-6:1994 - Mechanical properties of fasteners -- Part 6: Nuts with specified proof load values -- Fine pitch thread 상세보기
ISO 898-1:2013 - Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread 상세보기
ISO 898-7:1992 - Mechanical properties of fasteners -- Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 상세보기
ISO 898-1:2013 - Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread 상세보기
ISO 898-3:2018 - Mechanical properties of fasteners made of carbon steel and alloy steel — Part 3: Flat washers with specified property classes 상세보기
ISO 898-2:2022 - Fasteners — Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes 상세보기
ISO 898-3:2018/Amd 1:2020 - Mechanical properties of fasteners made of carbon steel and alloy steel — Part 3: Flat washers with specified property classes — Amendment 1 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
