관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Pulps — Estimation of dirt and shives — Part 4: Instrumental inspection by reflected light using Equivalent Black Area (EBA) method
| 분야 | ISO/TC 6 : Paper, board and pulps |
|---|---|
| 적용범위 | ISO 5350-4:2006 specifies a method using instrumental inspection by reflected light for the estimation of visible dirt and shives in pulp manufactured in sheets, in terms of Equivalent Black Area (EBA) of dirt specks within the physical area range of 0,02 mm2 to 3,0 mm2. Using the algorithm prescribed in ISO 5350-4:2006, the maximum dirt size is limited to 3,0 mm2. Extension to other speck sizes (for example, those greater than 3,0 mm2 in physical area) may require changes in equipment, calculation procedures, or both, and is not covered in ISO 5350-4:2006. ISO 5350-4:2006 cannot be used for physical area measurements since it may not correctly measure the dirt specks for that mode of measurement. The specimen to be evaluated should have a brightness, as determined by ISO 3688, of 30 % or greater. It may be necessary to reform some pulp sheets into laboratory sheets, if the surface is too rough or textured. ISO 5350-4:2006 is also intended for recycled pulp. |
| 국제분류(ICS)코드 | 85.040 : 펄프 |
| 페이지수 | 10 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 5350-4:2006 | Pulps — Estimation of dirt and shives — Part 4: Instrumental inspection by reflected light using Equivalent Black Area (EBA) method | 2006-09-12 | 표준 |
ISO 5350-1:2006 - Pulps — Estimation of dirt and shives — Part 1: Inspection of laboratory sheets by transmitted light 상세보기
ISO 5350-2:2006 - Pulps — Estimation of dirt and shives — Part 2: Inspection of mill sheeted pulp by transmitted light 상세보기
ISO 5350-3:2007 - Pulps - Estimation of dirt and shives — Part 3: Visual inspection by reflected light using Equivalent Black Area (EBA) method 상세보기
ISO 1924-3:2005 - Paper and board — Determination of tensile properties — Part 3: Constant rate of elongation method (100 mm/min) 상세보기
ISO 5263-1:2004 - Pulps — Laboratory wet disintegration — Part 1: Disintegration of chemical pulps 상세보기
ISO 5269-2:2004 - Pulps — Preparation of laboratory sheets for physical testing — Part 2: Rapid-Köthen method 상세보기
ISO 5350-1:2006 - Pulps — Estimation of dirt and shives — Part 1: Inspection of laboratory sheets by transmitted light 상세보기
ISO 5350-2:2006 - Pulps — Estimation of dirt and shives — Part 2: Inspection of mill sheeted pulp by transmitted light 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
