관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Tractors for agriculture and forestry — Roll-over protective structures on narrow tractors — Part 1: Front-mounted ROPS
| 분야 | ISO/TC 23/SC 2 : Common tests |
|---|---|
| 적용범위 | This document specifies procedures for both the static and dynamic strength testing of roll-over protective structures (ROPS) front-mounted on narrow tractors. It defines the clearance zone and acceptance conditions for rigid or tiltable, front, two-post ROPS, including any associated rear fixtures, and is applicable to tractors so equipped having the following characteristics: — a ground clearance of not more than 600 mm beneath the lowest points of the front- and rear-axle housings (not considering lower points on the axle differential); — a fixed or adjustable minimum track width of one of the two axles of less than 1 150 mm; NOTE It is understood that the axle mounted with the wider tyres is set at a track width of not more than 1 150 mm. Tyre track width is adjustable so that the outer edges of the narrower tyres do not extend beyond the outer edges of the tyres of the other axle. Where the two axles are fitted with rims and tyres of the same size, the fixed or adjustable track width of the two axles is less than 1 150 mm. — a mass greater than 400 kg but less than 3 500 kg, unballasted, including the ROPS and tyres of the largest size recommended by the manufacturer; — fitted with roll-over protective structures of the dual-pillar type mounted only in front of the seat index point (SIP) and characterised by a reduced clearance zone attributable to the tractor silhouette. This document also specifies optional testing procedures for both seat anchorage points and folding efforts of front-mounted ROPS designed to fold. |
| 국제분류(ICS)코드 | 65.060.10 : 농용 트랙터 및 트레일러 |
| 페이지수 | 61 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 12003-1:2021 | Tractors for agriculture and forestry — Roll-over protective structures on narrow tractors — Part 1: Front-mounted ROPS | 2021-06-11 | 표준 |
| 2 | ISO 12003-1:2008 | Agricultural and forestry tractors — Roll-over protective structures on narrow-track wheeled tractors — Part 1: Front-mounted ROPS | 2008-07-23 | 구판 |
| 3 | ISO 12003-1:2002 | Agricultural and forestry tractors — Narrow-track wheeled tractors — Part 1: Front-mounted roll-over protective structures | 2002-10-22 | 구판 |
ISO 12003-2:2021 - Tractors for agriculture and forestry — Roll-over protective structures on narrow tractors — Part 2: Rear-mounted ROPS 상세보기
ISO 8909-2:2021 - Equipment for harvesting — Forage harvesters — Part 2: Specification of characteristics and performance 상세보기
ISO 8909-1:2021 - Equipment for harvesting — Forage harvesters — Part 1: Vocabulary 상세보기
ISO 15886-2:2021 - Agricultural irrigation equipment — Sprinklers — Part 2: Design and operation requirements 상세보기
ISO 12003-2:2021 - Tractors for agriculture and forestry — Roll-over protective structures on narrow tractors — Part 2: Rear-mounted ROPS 상세보기
ISO 15886-4:2019 - Irrigation equipment — Irrigation sprinklers — Part 4: Test methods for durability 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
