관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures
| 분야 | ISO/TC 45/SC 2 : Testing and analysis |
|---|---|
| 적용범위 | This document specifies methods for the determination of the compression set characteristics of vulcanized and thermoplastic rubbers at ambient (one method) or elevated temperatures (three methods, A, B, and C, depending on the way the test piece is released at the end of the test). The methods are intended to measure the ability of rubbers of hardness within the range 10 IRHD to 95 IRHD to retain their elastic properties at specified temperatures after prolonged compression at constant strain (normally 25 %) under one of the alternative sets of conditions described. For rubber of nominal hardness 80 IRHD and above, a lower compression strain is used: 15 % for a nominal hardness from 80 IRHD to 89 IRHD and 10 % for a nominal hardness from 90 IRHD to 95 IRHD. NOTE 1 When rubber is held under compression, physical or chemical changes that prevent the rubber returning to its original dimensions after release of the deforming force can occur. The result is a set, the magnitude of which depends on the time and temperature of compression as well as on the time, temperature, and conditions of recovery. At elevated temperatures, chemical changes become increasingly more important and lead to a permanent set. NOTE 2 Short-time compression set tests, typically for 24 h, at elevated temperatures are commonly used as a measure of the state of cure, a means of material classification, and a specification to ensure the quality of a compound. Longer tests, typically for 1 000 h, at elevated temperatures take account of the effect of ageing and are often used to predict service performance, including that of sealing materials. Short-time tests at ambient temperature show mainly the effect of physical changes (re-orientation of the molecular chains and the fillers). |
| 국제분류(ICS)코드 | 83.060 : 고무 |
| 페이지수 | 14 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 815-1:2019 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures | 2019-11-26 | 표준 |
| 2 | ISO 815-1:2014 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures | 2014-08-20 | 구판 |
| 3 | ISO 815-1:2008 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures | 2008-01-28 | 구판 |
ISO 815-2:2019 - Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures 상세보기
ISO 815-2:2019 - Rubber, vulcanized or thermoplastic — Determination of compression set — Part 2: At low temperatures 상세보기
ASTM D4060-19 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser 상세보기
ASTM D573-04(2019) - Standard Test Method for Rubber—Deterioration in an Air Oven 상세보기
ISO 37:2017 - Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties 상세보기
ISO 23529:2016 - Rubber — General procedures for preparing and conditioning test pieces for physical test methods 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
