관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Coating powders — Part 1: Determination of particle size distribution by sieving
| 분야 | ISO/TC 35/SC 9 : General test methods for paints and varnishes |
|---|---|
| 적용범위 | This document specifies a method for the determination of the particle size distribution of coating powders by sieve analysis. Particle size distributions with a maximum of less than 100 µm is determined by laser diffraction, ISO 8130‑13. This method is used especially for determining the oversize material or for the presence of contamination and can be used as a quality control procedure ("go"/"no go" test) by checking the amount retained on a single sieve. The following particle sizes are typical for coating powders, however the particle size can deviate depending on the application: — thin-film technology: 1 µm to 63 µm; — electrostatic coating: 10 µm to 200 µm; — fluidizing-bed method: 100 µm and above. NOTE Sieves with a mesh size smaller than 32 µm are not practical and are likely to become blind during use. |
| 국제분류(ICS)코드 | 87.040 : 페인트 및 니스 |
| 페이지수 | 9 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8130-1:2019 | Coating powders — Part 1: Determination of particle size distribution by sieving | 2019-04-01 | 표준 |
| 2 | ISO 8130-1:1992 | Coating powders — Part 1: Determination of particle size distribution by sieving | 1992-12-03 | 구판 |
ISO 8130-9:1992 - Coating powders — Part 9: Sampling 상세보기
ISO 8130-4:1992/Cor 1:1993 - 상세보기
ISO 8130-7:2019 - Coating powders — Part 7: Determination of loss of mass on stoving 상세보기
ISO 8130-11:2019 - Coating powders — Part 11: Inclined-plane flow test 상세보기
ISO 8130-12:2019 - Coating powders — Part 12: Determination of compatibility 상세보기
ISO 13320:2020 - Particle size analysis — Laser diffraction methods 상세보기
ISO 7625:2012 - Sintered metal materials, excluding hardmetals — Preparation of samples for chemical analysis for determination of carbon content 상세보기
ISO 3923-2:1981 - Metallic powders — Determination of apparent density — Part 2: Scott volumeter method 상세보기
ASTM F2971-13(2021) - Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing 상세보기
ASTM B923-21 - Standard Test Method for Metal Powder Skeletal Density by Helium or Nitrogen Pycnometry 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
